background image

Radio control model
R/C Flugmodell

MONTAGEANLEITUNG

INSTRUCTION MANUAL

SPECIFICATIONS

Wingspan                                               48in.
Length                                                    36in.
Electric Motor                       (See next page)
Radio                            4 Channel / 4 Servos

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

TECHNISCHE DATEN

Spannweite                                    1200mm
Lange                                               915mm
Elektroantrieb             (siehe nächste Seite)
Fernsteuerung                4 Kanal / 4 Servos

Designed for brushless electric motors

 

Entwickelt für Brushless Elektro Motoren 

AIRACOBRA

VQA113

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for Airacobra P-39





















Reviews: