background image

SERVICES UPDATES

SERVICE UPDATES

February 2019

Updated PILOT, THERMOCOUPLE
ASSEMBLY.

November, 2018

Added TIS Document List.

TIS DOCUMENT LIST - 900RX SERIES

 

SERVICE TAB

Document Title

Document Type

900RX Series Heavy Duty Gas Griddles Service Manual Service Manual

 

SERVICE TAB (Multimedia)

Document Title

Document Type

Repairing Flood-Damaged Food Equipment

Misc

900RX Series Heavy Duty Gas Operation & Installation
Manual

Operator

AGE, AGM, 900RE, 900RX, and ASA Series Gas Griddle
Grease Chute P/N 498234-A Installation Instructions

Service Instructions

Fundamentals of Gas

Service Instructions

Rating Plate Locations on Current Vulcan-Hart/Wolf
Range Equipment

Technical Service Bulletin (TSB)

TSB 0842 4 Position/3 Heat Switch - Ranges, Ovens,
Broilers

Technical Service Bulletin (TSB)

TSB 1037A Hobart to Vulcan "Common" Model Cross
Reference List

Technical Service Bulletin (TSB)

TSB 1301 Onwatch Quicklook 72 for Gas Cooking
Equipment

Technical Service Bulletin (TSB)

TSB 682 Griddle Lead Wire Upgrading

Technical Service Bulletin (TSB)

RobertShaw FS Flame Switch Recall Vulcan & Wolf
Equipment Effected - PN 713933

Temporary Service Instructions (TSI)

 

PARTS TAB

Document Title

Document Type

900RX and MSA Heavy Duty Gas Griddles Parts Catalog Parts Catalog

 

Heavy Duty Gas Griddles - SERVICES UPDATES

Page 3 of 19

F25383 (0219)

Summary of Contents for ASA24




















Reviews: