background image

First issue dated 09 October 2017 
Rev.1 dated 08 January 2019 

 

Page

 1 

of 

19  

Vulcanair S.p.A. 

via G. Pascoli, 7 
80026 Casoria (NA) 

– Italia 

Tel +39 081 5918111 
Fax +39 081 5918172 
info@vulcanair.com 
www.vulcanair.com

 

V1 series

 

 

   Approved by Vulcanair Design Organisation 

The  technical  content  of  this  document  is  approved  under  the  authority  of  DOA  No. 

EASA.21J.009

.                             

Operator  obligations  with  regards  to  inspections,  modifications  and/or  other  technical  directives  and  their  times  of 
compliance are laid out in the relative 

Airworthiness Directives

 

SERVICE BULLETIN 

No. VA-03 Rev. 1 

(Supersedes the previous issue approved on 02 November 2017)

 

 

Design Organisation Approval No. AS-SB/19/002 dated 25 January 2019 

 

 
 

INFORMATION 

 
 

SUBJECT:   AIRCRAFT CONVERSION FOR GLIDER TOWING 
 

NOTE 

This  revision  is  being  issued  to  add  the  new  Kit 
applicable to V1.0 aircraft from s/n 1020 onwards, 
and to fix typing errors.
 

 
1. GENERAL  

1.1

 

AIRCRAFT AFFECTED 

Vulcanair V1.0. 

1.2

 

PURPOSE 

The  purpose  of  this  Service  Bulletin  is  to  supply  information  to  convert  aircraft  for  glider 
towing. 

1.3

 

DESCRIPTION 

Compliance  with  this  Service  Bulletin  requires  the  installation  of  the  Kit  SB_VA-03/A,  or 
SB_VA-03/B as applicable, to be carried out in accordance with the instructions in paragraph 2 
hereunder: 

 

Summary of Contents for V1 series




















Reviews: