background image

VXL Instruments Ltd

Itona TC61yy/TC63yy 

Hardware User’s Guide 

Installation  

Installation 

  

Step One: Unpack 

Unpack the unit taking care not to drop the product whilst removing from the packaging. 

The carton in which the product was shipped to you contains the following: 

 

 

Itona TC61yy / TC63yy 

 

Power Cord (Optional) 

 

Wall Mounting Bracket –Single side 

 

 

When you open the carton, if you find any discrepancy between the contents of the carton and the 
above list, contact the dealer or reseller from whom you have purchased the product, immediately. 

N

OTE

:

 

P

LEASE RETAIN THE ORIGINAL CARTON AND PACKING MATERIAL

.

 

T

HEY WOULD BE REQUIRED TO 

AVOID DAMAGE DURING TRANSIT 

(

IF REQUIRED IN FUTURE

). 

Step Two: Prepare 

1.  The site where you want to install the product must have the following 

 

 100~240V AC, 1.2A, 50/60 Hz, 3-pin power Inlet for client (Itona TC61yy / TC63yy).  

N

OTE

:

 

E

NSURE THAT THE POWER INLET PLUG IS PROPERLY REGULATED AND EARTHED

.

 

A

 FLOATING 

GROUND 

/

 CHASSIS COULD CAUSE AN ELECTRIC SHOCK

.

 

 

 

Well ventilated, clean, dry and dust free atmosphere. 

 

Ensure a minimum space of 2 inches (5 cm) on all sides of the unit for efficient convection 
cooling. 

 

The product can only be used in vertical position 

 

 

 Caution – This Product cannot be placed flat on desk as it will block the ventilation opening and  

                  affect the heating effect. 

 

 

 

Note: - For more Details – Refer to Installation and Best Practices Guide. 

 

 

 

 

 

 

 

 

9

9

Summary of Contents for Itona TC61yy



















Reviews: