Page 8
Page 9
SET UP & USE
• Foods frozen in this compartment
must be consumed within 5 days
after storage. This compartment
is not cold enough for long term
storage.
• To release frozen ice cube tray from
the bottom of the compartment,
pour warm water around it. Boiling
water should not be used as it
can damaged the interior cabinet.
Metal objects, such as, screwdrivers
or sharp knives can damage and
puncture the cooling system tubing.
Do not wash the ice cube tray in a
dishwasher; only wash in lukewarm
water.
1. Carefully tilt the shelf up and slide
forward until the shelf has been
completely removed.
2. Slide the shelf back to replace.
FREEZER COMPARTMENT
FREEZER INTERIOR SHELF
OPERATION INSTRUCTIONS
NOTE:
· If the freezer has been placed in a
horizontal or tilted position for any
period of time wait 24 hours before
plugging the unit in.
• The settings of the temperature
control are "OFF, 1, 2, 3, 4, 5, 6."
Adjust the temperature control
to the setting that best suits your
needs. The setting of "3" should be
appropriate for home or offi ce use.
• Turning the temperature to “OFF”
position will shut off the cooling
cycle, but does not turn off the
electrical power to the unit.
NOTE:
· Wait 3-5 minutes before restarting if
you unplug the freezer. The unit may
fail to operate properly if restarted
too quickly.
· If the ambient temperature is too
high, the freezer may not reach the
desired target temperature.
· Large amounts of foods will lower the
cooling effi ciency of the appliance.
· If you choose to change the
thermostat setting, adjust thermostat
control one increment at a time.
Allow several hours for temperature
to stabilize between adjustments.
TEMPERATURE CONTROL
SET UP & USE
Before reversing the door, ensure the
appliance is unplugged and empty.
Provide additional support for the doors
while hinges are being removed. Do not
depend on the door magnets to hold
the door in place. It is recommended
that two people perform this task. DO
NOT lay the appliance completely fl at as
this may damage the coolant system.
FREEZER DOOR REVERSAL
1. Remove any loose items from inside
the freezer (e.g. drip pan, ice tray,
etc.)
2. Using a fl at head screwdriver
remove the top hinge cover (A).
3. Loosen and remove the two screws
(B) using a Phillips head screwdriver
while holding the upper hinge in
place.
4. Remove the upper hinge (C) and
carefully lift off the door. Place the
door safely to the side.
5. Using a fl at head screwdriver
remove the screw hold plug (D)
from the opposite side and insert the
plug into the screw hole openings of
the just removed screws.
6. Carefully lay the freezer on its back
on a fl at secure area.
7. Using a Phillips head screwdriver,
loosen and remove the two screws
(E) holding the bottom hinge (F) in
place. Place the hinge and screws to
the side momentarily.
8. Remove the screw-type leveling
leg (G) from the opposite side and
screw it into the exposed hole on
the side from which the bottom
hinge was removed.
9. Place the bottom hinge (F) on the
opposite side and insert and tighten
the two screws (E) securely.
10. Place the freezer in its upright
position. Remove the door plug (H)
on the top of the door and insert it
fi rmly in the hole on the opposite
side. Align the hole in the door
bottom with the pin of the bottom
door hinge (F) and gently push
down until fi rmly in place.
11. Holding the door in the open
position place the pin of the upper
door hinge (C) into the hole located
on the top of the door. Align the
screw holes of the upper hinge (C)
with the screw holes on the top
corner of the cabinet and insert and
tighten loosely the two screws (B).
12. Check that the door is aligned and
level and then securely tighten the
upper hinge screws.
13. Replace the upper hinge cover (A)
by gently snapping it into place
A
B
C
H
E
F
D
G