background image

Safety Information 

Attention! Important safety instructions. Please read 

this manual thoroughly before using this product. 

 

Electrical Safety

 

Always unplug this adjustable bed frame from the electrical outlet before any maintenance 

or cleaning of the frame. To safely disconnect, make sure all of the controls are in the off 

position, and then remove the plug from the outlet. To prevent fire or shock hazard, do 

not expose this unit to moisture. Keep the power cord away from heated surfaces. Do not 

operate this adjustable bed frame and contact the manufacturer for repair if (1) it is not 

working properly, (2) it has a damaged cord or plug, (3) it has been dropped or damaged 

or (4) has been dropped into water.

Electrical Grounding 

This product is equipped with a polarized or grounded electrical power cord. The power cord 

will only fit into a grounded, electrical surge protection device (not included) or a grounded 

electrical outlet. The use of adapters is not recommended unless the outlet is checked by a 

qualified electrician to ensure the proper grounding of the adapter.  

For optimal safety, your adjustable bed should be plugged into a surge 
protector. 

Electrical Rating 

Input—100-240V, 50/60Hz, 1.6A; Output 29VDC, 2.0A 

Battery Precautions 

 

Please follow these precautions when using bat-

teries in this adjustable bed frame:

1. Danger of explosion if the battery is incorrectly replaced. Replace only with the 

6LR61 9V batteries and LR03 AAA batteries. 

2. Do not mix different types of batteries together (Alkaline, Rechargeable and 

Carbon-Zinc) or old batteries with new batteries. 

3. Be sure to follow the correct polarity when installing new batteries as indicated 

in the battery compartment. 

4. If the adjustable bed is not going to be used for a long period of time, remove 

the batteries from the battery compartment to prevent damage or injury 
from possible battery leakage. 

5. Do not attempt to recharge a battery that is not intended to be recharged. This 

may result in an overheating of the battery or rupture that could result in injury. 

In Home Use & Hospital Disclaimer 

Your adjustable bed frame is strictly designed for in-home use only. It is NOT designed for 

hospital use and is NOT designed to meet hospital standards. Do not use this bed with TENT 

TYPE oxygen therapy equipment or near explosive gases.   

Lubrication and Cleaning 

Your adjustable bed is designed to be maintenance free. The lift motors are permanently 

sealed and lubricated, no additional lubrication is required. Do not apply any lubricant to 

lift motor lead screws or any nylon nuts or the base may inadvertently creep downward 

from the elevated position.   

Warranty Warning 

Please do not open any control box, motors or hand controls (with the exception of the 

battery compartment, if equipped). The product warranty may be void if any of these 

components are tampered with. Do not attempt to alter component wiring or adjust or 

modify the structure of the product in any way or the warranty will be void. Only WSP 

can authorize any repairs or replacement of parts on your adjustable bed.

Pets and Small Children Warning 

Immediately dispose of all packing materials as it may pose a smothering risk to small 

children and pets To avoid injury, it is not advised to allow children and small pets to 

play on or under the bed. Children should not operate your adjustable bed without adult 

supervision.

Consumers with Pacemakers 

Your adjustable bed may be equipped with a massage motor that produces a vibrating 

motion. It is possible that some pacemakers may interpret this type of motion as a false 

sense of movement and/or exercise. This may or may not affect your pacemaker. If you 

have any concerns, please consult your physician. 
Your adjustable bed also contains Neodymium (magnets) which may interfere with 

devices such as pacemakers, ICD’s and any other device sensitive to magnetic fields. It is 

strongly recommended that owners of such medical devices consult their physician prior 

to using this product. 

Product Ratings 

The lift motors in your adjustable bed are NOT designed for continuous use. Reliable 

operation and full life expectancy will be attained as long as the lift motors do not operate 

more than 2 minutes over an 18 minute period, or approximately 10% duty cycle. To 

ensure reliable functionality and full life of your adjustable bed, do not attempt to exceed 

these limits. 

Attempting to circumvent or exceed this rating will shorten the life 

expectancy of your adjustable bed and may void the warranty. 

Acoustics 

Your adjustable bed may contain the optional massage motor. This massage function will 

emit a noticeable tone during operation. As the massage intensity level is increased, the 

volume of the tone will increase. The volume of the tone is directly related to the location of 

your adjustable bed. As an example, the surrounding environmental noise that might have 

been present in the showroom where you purchased your adjustable bed could have covered 

some of the noise from your adjustable bed massage motors. When your adjustable bed was 

installed in your home you might notice an increase in volume in wood floorings or carpets. 

In some normal base operations, you might notice some noise coming from the wheels 

which allow your adjustable bed to maintain its distance from the wall. These wheels will 

make contact with the steel platform supports of your adjustable bed creating a contact noise 

when you enter, exit or shift weight while on the bed. This is normal. 

FCC Compliance

This device complies with part 15 of the FCC rules. 

Operation  is  subject  to  the  following  two  conditions:  (1) This  device  may  not  cause 

harmful interference; (2) This device must accept any interference received, including 

interference that may cause undesired operation. To comply with the FCC RF exposure 

compliance requirements, no change to the antenna or the device is permitted. Any 

change to the antenna or the device could result in the device exceeding the RF exposure 

requirement and void user’s authority to operate the device. 
Radio Frequency is 2.4-2.48 GHz 

Weight Restrictions 

The structure of your adjustable bed will support the recommended weight when 

distributed evenly across the bed. The adjustable bed is not designed to support or lift this 

amount in the head or foot sections alone. You should enter and exit your adjustable bed 

with the base in the flat (horizontal) position. 

DO NOT STAND ON THE BASE AT 

ANY TIME. DO NOT SIT ON THE HEAD OR FOOT WHILE IN THE RAISED 

POSITION.

  The  recommended  weight  limits  are  Twin/TwinXL/Full/FullXL/Split 

Queen/Queen/Split Cal King/Split King: 850 lbs; Single Piece King 650 lbs. Exceeding 

this weight restriction could damage the bed and/or cause injury and will void the warranty. 

Moving After Installation 

Do not place adjustable bed base vertically on its head or foot sections. This may cause 

injury to persons or damage to the base. 

Fabric Cleaning Information 

Spot clean only with a water based shampoo or a foam upholstery cleaner. Pretest a small, 

inconspicuous area before proceeding. Do not over wet or  use solvents to spot clean. Hot 

water extraction or steam cleaning is not a recommended cleaning method. To prevent 

overall soiling, frequent vacuuming or light brushing with a non-metallic stiff bristle brush 

to remove dust or grime is recommended. 

PLEASE SAVE THIS MANUAL!

Summary of Contents for COMFORT-n-MOTION S2766













Reviews: