background image

FRONT PANEL CONTROLS

       Incoming signals  will have up to 20dB of compression introduced.
       The EQplus compressor circuitry contains a limiter that is preset 
       at the factory. The limiter is set  to limit the processed signals to 
       375 millivolts (-9 dB). When this level is reached the 1-st  yellow 
       LED on the bar graph will be on and the top Red (Limiting)  LED 
       will turn on.  Additional increases in audio level, using either the
       Audio Input Gain Potentiometer or the Equalizer Potentiometers, 
       will result in a small  increase in output from the compressor’s 
       circuitry. The good news is that the EQplus can produce high 
       levels of compression while maintaining fidelity and very low 
       distortion levels. The RF compressors in many radio’s have 
       difficulty attaining high levels of compression with low levels 
       of distortions. RF compressors roll off the low end audio response 
       of the signals they process. The net result of the EQplus 
       compressor is up to 20dB of signal  compression with  very low 
       distortion and little to no change in overall audio bandwidth. .
    

(12)  Compressor / Downward Expander Downward Expander 
         Level (DE LEVEL) POTENTIOMETER (R47)

          
       This potentiometer works only if the Compressor / Downward 
       Expander switch (10) is on. The Downward Expander  removes  
       unwanted audible sounds such as fan noise. The Downward 
       Expander is operated by turning  the DE LEVEL Control clockwise 
       just to the point where unwanted sounds are removed. 

(13)  EFFECTS PROCESSOR PROGRAM SELECT / OFF 
        SWITCH (S4)
     
       

This 3 position toggle switch is used to select one of two effects or 

        to turn the Effects Processor off. When the Effects Processor is 
        off the Effects Processor  Delay and Level controls will not modify
        internal EQplus audio. The toggle switch in position 1 selects 
        Effect 1. Effect 1 emulates dampening sound  reflecting multiple 
        times  from a surface.  The toggle switch in the position 2 selects  
        Effect 2. Effect 2 emulates sound reflecting once from a surface.  
         
     

     
           

-8-

Summary of Contents for AUDIO PROCESSOR






















Reviews: