background image

3   

Troubleshooting and Testing 

24

Meritor WABCO

 Maintenance Manual 34 (Revised 03-16)

3 Troubleshooting and Testing

Hazard Alert Messages

Read and observe all Warning and Caution hazard alert messages in 
this publication. They provide information that can help prevent 
serious personal injury, damage to components, or both.

WARNING

To prevent serious eye injury, always wear safe eye protection 
when you perform vehicle maintenance or service.

Remove all pressure from the air system before you 
disconnect any component, including the desiccant cartridge. 
Pressurized air can cause serious personal injury.

Park the vehicle on a level surface. Block the wheels to 
prevent the vehicle from moving. Support the vehicle with 
safety stands. Do not work under a vehicle supported only by 
jacks. Jacks can slip and fall over. Serious personal injury and 
damage to components can result.

NOTE: 

The pressure protection elements are not serviceable on the 

System Saver 1200 Plus with MCP. The entire air dryer needs to be 
replaced if these parts are not operating effectively.

Maintenance

To keep your Meritor WABCO air dryer operating efficiently, the 
routine maintenance in Table C is recommended.

Table C

Action

Interval

Ensure the dryer purges when compressor unloads.

Weekly.

Drain the purge tank (dedicated purge tank dryers).

Weekly, or as recommended by the manufacturer.

Check for moisture in the system by opening the drain cock on vehicle 
system reservoirs slowly.

Weekly, or as recommended by the manufacturer, whichever is 
most frequent.

Replace the standard desiccant cartridge.

Every two to three years, or more often depending on usage, 
vocation, and condition of compressor.

Whenever compressor is rebuilt.

Replace the coalescing cartridge.

Every one to two years.

Summary of Contents for 1200 Plus MCP





















































Reviews: