88
11.
Recommendations for application and operation
11.1
Swivelling of the milling head
In order to produce bore holes and chamfering at an angle which diverges from the normal vertical
position of the milling head, the milling head can be swivelled up to 90° either to the right or to the
left.
If an adjustment is intended please proceed as follows:
After loosening (turn to the left) the lock nut (part-no. 7) turn the hexagon nut as far to the right
against the housing of the tool spindle until the index pin (part-no. 4) can be pulled out by hand.
Loosen both the high nut (part-no. 30) and the hexagon nut (part-no. 31) on the vertical slide by
then turning to the left.
Now the milling head can be swivelled to the desired degree to the left or to the right. In order to fix
the milling head in this position, tighten both the high nut and the hexagon nut again.
In order to bring the milling head back to its normal position, loosen the high nut and the hexagon
nut on the vertical slide and bring the vertical slide back to its upright position. After turning back the
hexagon nut on the index pin, the latter can be pushed into the opening in the work spindle housing
by hand. Now, both the hexagon nut and the lock nut of the index pin as well as the hexagon nut
and the high nut on the vertical slide can all be tightened.
Summary of Contents for F1410 LF
