89
12.
Unit for lubrication coolant
The unit for lubrication coolant consists of:
1. Tray with lubrication coolant sump which collects the lubrication coolant mixture fort he feed pump.
Content:
Coolant unit
Order No. 11264
13 litres
Safety machine cabin Order No. 1640090
42 litres
2. Feed pump with the following electrical data:
nominal voltage 230 V
frequency 50/60 Hz
nominal current input 0,4A
nominal output 0,07 kW
ON-OFF switch and mains lead with a length of 2 m complete with earthed plug
3. Adjustable, flexible pressure tubing with stop valve and nozzle: for transporting the lubrication
coolant to the processing point.
An increasing number of customers wish to include this fixture in their order so as to take
advantage of “wet processing” for the production of their goods/workpieces and to:
to cool and lubricate, in particular during lengthy processing
when processing high alloy steel and aluminium
extends working life of tool
to improve the surface finish and accuracy of the workpieces
to reduce friction heat
to prevent built-up edges
When using lubrication coolants, especially water based emulsions, a number of health and safety
measures must be observed:
1. use concentrated products free of nitrates
2. use concentrates without secondary amins
3. use products with the lowest possible allergy potential
4. When mixing a refill of lubrication coolant, please observe the following:
clean/rinse the circulation system (tray/filter)
determine the concentration necessary to meet the technical demands
(concentrate: water 1:5 – 1:30)
check the water has a low level of nitrates (< 50 mg NO 3-, test strip)
5. A cleaning plan should determine at what intervals the system should be cleaned of swarf and
other waste.
6. A service plan should determine the following:
when to check the concentration in use (daily/weekly)
when to check the pH values (weekly)
when to check/assess the bacteria count (monthly)
when to check the nitrate content (weekly)
(The information in brackets can be varied according to the production circumstances)
7. In order to reduce splashing, we recommend the attachment of a splash guard and/or reducing
amount sprayed from the nozzle.
8. Since steps to protect the skin must be taken, it is advisable to wear gloves and aprons. The
skin should be cleaned with acidic syndets without abrasive ingredients and rich cream should
be applied to regenerate the skin.
9. Please also adhere to the enclosed information on the general operating instructions.
Summary of Contents for F1410 LF
