background image

INTERCEPTORS

 

10

 

Wade

 

Drains

 ‐ 

11910

 

CR492,

 

Tyler,

 

TX,

 

75706

 ‐ 

Phone:

 

800

638

9537

 

Fax:

 

888

879

9233

 ‐ 

www.wadedrains.com

 

3

29

17

 

 

EXTENSIONS (Adjustable) 

In installations where the exact extension dimension required is unknown or where little notice has been provided to the installer 
advising of the need for an extension; integral and bolt on extensions are impractical due to the time necessary for their fabrication. 
Wade’s nationwide network of manufacturer's representatives stock adjustable extensions for immediate shipment to jobsites when 
these situations occur. The extension is adjustable and is secured to the interceptor similar to a fixed extension. After bolting the 
extension to the interceptor, the top is adjustable to grade.  

Installation Note 

If adjustable extension is install in areas other than on grade where fumes may seep from the adjustable extension connections, an 
optional rope seal is recommended.  The 1/2” diameter neoprene sponge gasket is installed in the annular space between the upper 
and lower housings.  For the slotted openings, it is recommended that these spaces be sealed with a elastomeric flex seal tape with 
good adhesion characteristics.  For slab on grade installations where it is desirable to seal the housing from back-fill, an aluminum foil 
duct tape is suitable. 

Summary of Contents for 5100











Reviews: