background image

 

4

  

EN-XXX_ECOplus-Solar-Storage_MA-201026-1WA10603

Figure 4  Drinking water connections (example): 

Air vent; 

10

 Magnesium protection anode with cable; 

11

 Cold water; 

12

 Hot water; 

13 

Safety 

unit; 

14

 Circulation pump; 

15 

Thermostatic mixer; 

16

 Check valve; 

17

 Filling and emptying tap

3.3  Connecting the Domestic Water 

Circuit

 

(Fig  4) Connect a safety unit (13) to the cold water sup-
ply and ideally position above the storage  This allows 
for easy maintenance of the safety group without having 
to 

empty 

the 

tank  

     

 

The storage tank might be damaged without safety 
group or when the safety group is closed off!  

 

The water expands when heated and thus high over-
pressure can build up in the system  Ensure that there 
is no shut-off valve between cylinder and safety valve  

 

Installation of a filling and emptying tap at the lowest 
storage connection (17) 

 

Fit a thermostatic mixer (15)  This assures that even 
when the storage tank is heated to its maximum tem-
perature the DHW temperature set at the thermostatic 
mixing valve will not be exceeded  If no thermostatic 
mixer is fitted, maximum vessel temperature must 
be limited to 65 °C at the solar controller  

 

 

Serious danger of scalding! 

 

  

The solar installation may heat the storage water to tem-
peratures of up to 95 °C.  

 

 

 

.  

The installation of a thermostatic mixing valve limits the 
tap temperatures to a safe temperature level 

 

Installation of a circulation pump if required (14)  The 
return should be taken from close to the tapping point  
The circulation pump should govern circulation ac-
cording to water temperature (temperature sensor) 
and with a timer 

 

The circulation control should be implemented in the 
most energy saving fashion according to the state of 
the art  

 

Installation of an air vent (9)  Part of the ECOplus con-
nection kit, part no  139 002 07 

13

15

14

17

11

12

16

9

10

8 Cold water connection

3 Circulation connection

CONVECTROL  

part of the ECOplus 

connection kit,  

part no  139 002 07

1 Hot water connection

16

9

10

8 Cold water connection

3 Circulation connection

1 Hot water connection

11

Summary of Contents for ECOplus









Reviews: