background image

© 1995 Wagner Spray Tech

19

All rights reserved.

1

2

3

4
5

6

8

7

11

10

9

12

Parts Diagram – Suction Set Assembly
0270174

ITEM PART NO. DESCRIPTION

QTY.

1

0270133

Suction tube assembly .................... 1
  (Includes Items 2 through 10)

2

0090622

Nut, suction ..................................... 1

3

0281314

Elbow, adapter, 3/4" x 1" ................. 1

4

0088931

Ring, snap ....................................... 1

5

0089882

Clamp .............................................. 1

6

0270360

Hose, suction .................................. 1

7

0270162

Filter housing and filter .................... 1

8

0270369

Filter ................................................ 1

9

0090621

Washer ............................................ 1

10

0088715

Fitting, return hose .......................... 1

11

0327226

Clamp .............................................. 1

12

0270363

Tubing, return .................................. 1

3

4

5

6

7

2

8

1

11

12

9

10

Parts Diagram - G-06 Spray Gun

ITEM PART NO. DESCRIPTION

1

0293004

G-06 gun assembly
(includes items 2 through 7)

2

0089731

Filter assembly
(includes items 3,4,5,6)

3

0043590

Spring

4

0089694

Seal, nylon

5

0089692

Housing filter

6

0043260

Washer

7

0089693

Fitting

8

0089959

Filter

9

0293303

Guide, hose

10

0154782

Tip, .011 (oil based materials)

0154783

Tip, .013 (oil based , latex paints and
stains)

0154784

Tip, .015 (extra thick materials)

11

0154680

Tip, body

12

0154693

Seal kit

NOTE: Part numbers may change without notice due

to improvements and modifications.

Summary of Contents for 0278712C





















Reviews: