background image

29

Control Pro 350 Extra Skid

GB

Problem

Cause

Remedy

The paint pattern is 

tailing.

• 

The paint is too viscous or contaminated.

 

• 

The spray nozzle is plugged.

• 

The spray nozzle is worn.

• 

The spray nozzle is blocked (if fitted)

• 

The inlet filter is clogged.

• 

The inlet valve is worn or damaged.

 

 

Thin or strain the paint.

 

Clean the spray nozzle and use the HEA filter set.

 

Replace the spray nozzle with a new nozzle.

 

Clean or replace the filter.

 

Clean the inlet filter.

 

Replace

Warning

If the supply cord of this appliance is damaged, it must only be 

replaced by a repair shop appointed by the manufacturer, because 

special purpose tools are required. 
The wires in this mains lead are coloured in accordance with the 

following code:

green/yellow = earth        blue = neutral         

brown = live

As the colours of the wires in the mains lead of this appliance may not 

correspond with the coloured markings identifiying the terminals in 

your plug, proceed as follows:

• 

The wire which is coloured green and yellow must be connected 

to the terminal in the plug which is marked with the letter E or by 

the earth symbol or coloured green or green and yellow.

• 

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

• 

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured brown.

• 

Should the moulded plug have to be replaced, never re-use the defective plug or attempt to plug it into a different 13 A socket. 

This could result in an electric shock.

• 

Should it be necessary to exchange the fuse in the plug only use fuses approved by ASTA in accordance with BS 1362. Only 13 

Amp fuses may be used.

• 

To ensure that the fuse and fuse carrier are correctly mounted please observe the provided markings or colour coding in the 

plug.

• 

After changing the fuse, always make sure that the fuse carrier is correctly inserted. With out the fuse carrier, it is not permissible 

to use the plug.

• 

The correct fuses and fuse carriers are available from your local electrical supplies stockist.

Summary of Contents for CONTROL PRO 350 EXTRA SKID





















Reviews: