99
FineCoat 9700
PT
terrupções enquanto estiver a pulverizar o objecto.
Em caso de formação excessiva de neblina de tinta, regular a
quantidade de ar e de material, bem como a distância relati-
vamente ao objecto.
10
INTERRUPÇÃO DO TRABALHO
1. Rodar o botão de regulação de material para a direita até
ao batente. Assim, a pistola de pintura fica segura contra o
funcionamento não intencional.
2. Desligar o aparelho usando o interruptor principal do
aparelho de base.
3. Introduzir a pistola de pulverização no alojamento da pistola
do aparelho.
Se utilizar materiais de revestimento de secagem
rápida ou de dois componentes, enxaguar sempre
o aparelho com um produto de limpeza adequado
durante o período de processamento, uma vez que,
caso contrário, o aparelho apenas poderá ser muito
dificilmente limpo.
Importante: Através do aquecimento, o tempo de
actuação do material do material pode alterar-se. Por
conseguinte, entrar em contacto com o fabricante
do material.
11
TRANSPORTE
1. Enrolar o cabo de alimentação em volta do aparelho de
base.
2. Introduzir a pistola de pulverização no alojamento da pistola
do aparelho.
3. Desaparafusar a mangueira de ar do aparelho base.
4. Enrolar a mangueira de ar e apertar com uma fita de fixação.
12
DESLIGAR E LIMPAR O APARELHO
1. Desligar o aparelho.
2. Desenroscar o depósito.
Esvaziar o restante material de revestimento existente no
depósito de tinta para o recipiente original.
3. Rodar o tubo ascendente para fora da vedação do depósito.
(Fig. 14)
Com o conjunto de escovas fornecido, o
acessório pulverizador pode ser limpo de forma
particularmente eficaz (exemplos fig.15 e 16).
4. Limpar o tubo ascendente e o bocal de sucção com uma
escova de limpeza. (Fig. 15)
5. Limpar o orifício de saída de ar. (Fig. 14, 2)
ATENÇÃO! Nunca limpe os vedantes, a
membrana e os furos do injector ou do
ar da pistola pulverizadora com objectos
metálicos afiados. O tubo de ventilação
e a membrana são apenas parcialmente
resistentes a solvente. Não os mergulhar
em solvente, mas limpá-los apenas.
6. Desenroscar o anel regulador (fig. 2, 4), retirar o suporte
para bico de jato de ar (3) e o disco antivibrações de mola
(5).
7. Desaparafusar o bico. (Fig. 3)
8. Limpar o suporte para bico de jato de ar, o bico e a agulha
com a escova e solvente ou água. (Fig. 16)
Limpar com especial cuidado os intervalos no pino
(fig. 16, 7)
9. Limpar o exterior da pistola pulverizadora e do depósito
com um pano embebido em solvente ou em água. Para a
rosca (fig. 16, 6) utilizar a escova multifuncional.
10. Lubrificar ligeiramente os pontos marcados com óleo isento
de silicone (fig. 17).
11. Montar novamente as peças (ver “montagem”).
12.1 MONTAGEM
ATENÇÃO! Para a montagem, observar
rigorosamente os passos indicados em
baixo. Caso contrário, a pistola pode ser
danificada.
1.
Inserir o bico na pistola e apertar.
2.
Inserir o disco antivibrações de mola e o suporte para bico
de jato de ar na pistola e aparafusar o anel regulador.
3. Rodar o tubo ascendente com a vedação do depósito no
corpo da pistola.
Se a pistola de pulverização de pintura não for
utilizada durante um período longo de tempo, esta
deverá ser preparada, após a limpeza, com óleo
isento de silicone.
INTERRUPÇÃO DO TRABALHO/ TRANSPORTE/
DESLIGAR E LIMPAR O APARELHO
Summary of Contents for FINE COAT 9700
