23
FinishControl 4000 18V
EN
CORRECTION OF MALFUNCTIONS
15
CORRECTION OF MALFUNCTIONS
MALFUNCTION
CAUSE
REMEDY
The unit will not start
•
Battery flat, faulty or incompatible
•
Device overheated
•
Battery flat, faulty or incompatible
•
Let the device cool down approx. 10 minutes,
check the air filter, do not cover the intake slots
No coating material emerges
from the nozzle
•
Nozzle clogged
•
Material volume setting too low
•
Paint container seal damaged
•
No pressure build-up in container
•
Container empty
•
Ventilation hose loose/damaged
•
Feed tube loose
•
Feed tube / feed tube filter clogged
•
Air vent on feed tube blocked
•
Diaphragm stuck
•
Clean
•
Increase volume
•
Replace
•
Tighten container
•
Refill
•
Insert or replace
•
Insert
•
Clean or use another filter
•
Clean
•
Remove and clean (see section 14.2)
Coating material drips from the
nozzle
•
Air cap, nozzle or needle soiled
•
Spray attachment incorrectly
assembled
•
Nozzle loose
•
Nozzle seal is missing or worn
•
Nozzle worn
•
Needle worn or damaged
•
Clean
•
Assemble correctly (see section 13.1)
•
Tighten Union nut
•
Insert an intact nozzle seal
•
Change
•
Replace the needle (service set 2434518)
Atomisation too coarse
•
Material volume too large
•
Nozzle contaminated
•
Viscosity of coating material too high
•
Too little pressure build-up in
container
•
Air filter heavily soiled
•
Amount of air too low
•
Air cap assembled incorrectly
•
Reduce volume
•
Clean
•
Dilute further
•
Tighten container
•
Change (see section 14.1)
•
Increase volume
•
Snap air cap properly into place (fig. 16)
Spray jet pulsates
•
Coating material in container running
out
•
Nozzle seal is missing or worn
•
Air filter heavily soiled
•
Feed tube loose
•
Feed tube / feed tube filter clogged
•
Refill
•
Insert an intact nozzle seal
•
Change (see section 14.1)
•
Insert
•
Clean or use another filter
Coating material causes “paint
tears
•
Too much coating material applied
•
Distance too small
•
Incorrect spray attachment
•
Reduce volume
•
Increase distance
•
Use another spray attachment
Excessive paint mist (overspray)
•
Distance to the object too large
•
Too much coating material applied
•
Amount of air too high
•
Coating substance over-diluted
•
Incorrect spray attachment
•
Reduce distance
•
Reduce volume
•
Reduce volume
•
Reduce degree of dilution
•
Use another spray attachment
Paint in the ventilating hose
•
Diaphragm soiled
•
Diaphragm defective
•
Clean the diaphragm (see section 14.2)
•
Replace the diaphragm (see section 14.2)
Summary of Contents for FINISH CONTROL 4000 18V
