35
FinishControl 4000 18V
FR
Témoin batterie
13
Vert
Orange
Orange clignotant
(la poignée vibre)
=
=
=
Charge suffisante de la batterie
Seuls de petits travaux sont encore
possibles
La batterie doit être chargée
Chargez/changez la batterie à temps. Si l'appareil
s'arrête brusquement pendant le travail, des
projections de matériau peuvent se produire.
9
MISE EN SERVICE
1. Dévisser le godet de la façade amovible.
2. Remplir avec le produit de revêtement préparé.
Ne pas dépasser
le niveau de rem-
plissage max. du
réservoir.
MAX
3. Poser le filtre sur le tube d’aspiration (fig. 8, 1).
Façade amovible StandardSpray
Poser le filtre adéquat sur le tube d’aspiration en
fonction du produit de revêtement utilisé:
Produits de revêtement très liquides
Filtre fin
(rouge)
Produits de revêtement visqueux
Filtre gros-
sier (blanc)
4. Visser solidement le godet sur la façade amovible.
5. Raccorder la façade amovible et l’appareil FC 3500 entre
elles. (Fig. 2)
6. Insérer la batterie.
Vérifier que la
batterie est bien
insérée. Une batterie
qui se détache
pendant l‘utilisation
peut entraîner des
dommages matériels
ou corporels.
7. Actionner l’interrupteur MARCHE / ARRÊT sur l’appareil
(la turbine fonctionne à la puissance minimale).
L’appareil est maintenant prêt à fonctionner (la turbine
fonctionne à la puissance minimale).
10
TECHNIQUE DE PULVÉRISATION
FinishControl a une gâchette avec 2 points de
poussée. Durant la première étape, la turbine règle
la pression de service préréglée. Lorsqu‘on appuie
plus fortement sur la gâchette, la peinture est pul-
vérisée.
Tirer la gâchette du pistolet.
Effectuez un essai de pulvérisation sur un morceau de carton,
afin de régler correctement le résultat de la pulvérisation, la
largeur du jet, les quantités de produit et d’air.
Tenir le pistolet verticalement à une distance régulière
comprise entre 3 – 10 cm par rapport à l’objet. (fig. 9)
Déplacer le pistolet régulièrement en sens transversal ou
vertical. Le déplacement régulier du pistolet est garant d’une
bonne qualité de surface.
Commencer le travail toujours à l’extérieur de l’objet et
éviter des interruptions si vous êtes sur l’objet.
Si la formation de brouillard est trop importante, chercher à
améliorer le réglage du débit de produit ainsi que la distance
à l’objet.
11
INTERRUPTIONS DE TRAVAIL
1. Arrêter l‘appareil.
2. Pour une interruption prolongée du travail, depressuriser
le réservoir en le dévissant brièvement et en le revissant
ensuite.
3. Nettoyer les orifices de la buse après avoir interrompu le
travail.
Lors de la mise en oeuvre de peintures à séchage
rapide ou de produits de revêtement à deux
composants, rincer sans faute le groupe à l'intérieur
du temps d'utilisation avec le produit de nettoyage
adéquat, sinon l'appareil ne pourra plus être nettoyé
que très difficilement ou risque même d'être
endommagé. Important: L‘échauffement influe sur
la vie en pot du produit. Nous vous recommandons
donc de consulter le fabricant.
12
TRANSPORT
ATTENTION ! Les récipients remplis doi-
vent être solidement bouchés pour être
transportés dans le coffret. Ne pas poser
le coffret sur le côté, quand il contient des
récipients remplis.
MISE EN SERVICE/ MISE EN SERVICE/ TECHNIQUE DE PULVÉRISATION /
INTERRUPTIONS DE TRAVAIL / TRANSPORT/ MISE HORS SERVICE ET NETTOYAGE
Summary of Contents for FINISH CONTROL 4000 18V
