10
FinishControl 5500
EN
14
CORRECTION OF MALFUNCTIONS
MALFUNCTION
CAUSE
REMEDY
The unit will not start
•
No mains voltage
•
Device overheated
•
Check
•
Unplug the power plug, let the device cool
down approx. 30 minutes, do not bend the
hose, check the air filter, do not cover the intake
slots
No coating material emerges
from the nozzle
•
Nozzle clogged
•
Material volume setting too low
•
Paint container seal damaged
•
No pressure build-up in container
•
Container empty
•
Ventilation hose loose/damaged
•
Feed tube loose
•
Feed tube / feed tube filter clogged
•
Air vent on feed tube blocked
•
Diaphragm stuck
•
Clean
•
Increase volume
•
Replace
•
Tighten container
•
Refill
•
Insert or replace
•
Insert
•
Clean or use another filter
•
Clean
•
Remove and clean (see section 13.2)
Coating material drips from the
nozzle
•
Air cap, nozzle or needle soiled
•
Spray attachment incorrectly
assembled
•
Nozzle loose
•
Nozzle worn
•
Needle worn or damaged
•
Clean
•
Assemble correctly (see section 12.1)
•
Tighten Union nut
•
Change
•
Replace the needle (service set 2434517)
Atomisation too coarse
•
Material volume too large
•
Nozzle contaminated
•
Viscosity of coating material too high
•
Too little pressure build-up in
container
•
Air filter heavily soiled
•
Amount of air too low
•
Air hose damaged
•
Air cap assembled incorrectly
•
Reduce volume
•
Clean
•
Dilute further
•
Tighten container
•
Change (see section 13.1)
•
Increase volume
•
Check and replace if necessary
•
Snap air cap properly into place (fig. 17)
Spray jet pulsates
•
Coating material in container running
out
•
Nozzle seal worn
•
Air filter heavily soiled
•
Feed tube loose
•
Feed tube / feed tube filter clogged
•
Refill
•
Replace
•
Change (see section 13.1)
•
Insert
•
Clean or use another filter
Coating material causes “paint
tears
•
Too much coating material applied
•
Distance too small
•
Incorrect spray attachment
•
Reduce volume
•
Increase distance
•
Use another spray attachment
Excessive paint mist (overspray)
•
Distance to the object too large
•
Too much coating material applied
•
Amount of air too high
•
Coating substance over-diluted
•
Incorrect spray attachment
•
Reduce distance
•
Reduce volume
•
Reduce volume
•
Reduce degree of dilution
•
Use another spray attachment
Paint in the ventilating hose
•
Diaphragm soiled
•
Diaphragm defective
•
Clean the diaphragm (see section 13.2)
•
Replace the diaphragm (see section 13.2)
CORRECTION OF MALFUNCTIONS
Summary of Contents for FinishControl 5500
