background image

English

© Wagner Spray Tech - All Rights Reserved 

3

Important Safety Information

WaRnInG - To reduce the risk of 

injury:

  1.  Always wear appropriate gloves, eye protection, 

clothing and a respirator or mask when 

painting.  Hazardous vapors – Paints, solvents, 

insecticides, and other materials can be harmful 

if inhaled or come in contact with body.  Vapors 

can cause severe nausea, fainting or poisoning.

  2.  Do not operate or spray near children.  Keep 

children away from equipment at all times.

  3.  Do not overreach or stand on an unstable 

support.  Keep effective footing and balance at 

all times.

  4.  Stay alert and watch what you are doing.
  5.  Do not operate the unit when fatigued or under 

the influence of drugs or alcohol.

  6.  Never aim spray gun at any part of the body.
  7.  Follow all appropriate local, state, and national 

codes governing ventilation, fire prevention, 

and operation. 

  8.  The United States Government Safety Standards 

have been adopted under the Occupational 

Safety and Health Act (OSHA).  These standards, 

particularly part 1910 of the General Standards 

and part 1926 of the Construction Standards 

should be consulted.

  9.  Use only manufacturer authorized parts.  User 

assumes all risks and liabilities when using parts 

that do not meet the minimum specifications 

and safety devices of the turbine manufacturer.

 10.  Power cord must be connected to a grounded 

circuit.

 11.  Do not spray outdoors on windy days.
 12.  Use only Wagner HVLP hose.

WaRnInG - To reduce the risk of 

electric shock:

  1.  Power cord must be connected to a grounded 

circuit.

  2.  Never submerge electrical parts.
  3.  Never expose the equipment to rain.  Store 

indoors.

  4.  Keep electrical cord plug and spray gun trigger 

free from paint and other liquids.  Never hold 

the cord at plug connections to support the 

cord.  Failure to observe may result in an 

electrical shock.

Important Electrical 

Information

Use only a 3-wire extension cord that has a 3-blade 

grounding plug and a 3-slot receptacle that will 

accept the plug on the product.  Make sure your 

extension cord is in good condition.  When using an 

extension cord, be sure to use one heavy enough 

to carry the current your product will draw.  An 

undersized cord will cause a drop in line voltage 

resulting in loss of power and overheating.  A 14 

gauge or 12 gauge cord is recommended.  If an 

extension cord is to be used outdoors, it must be 

marked with the suffix W-A after the cord type 

designation.  For example, a designation of SJTW-A 

would indicate that the cord would be appropriate 

for outdoor use.  

IMPORTanT:  Household use only.  Intended 

for indoor/outdoor use OnLY with materials 

having flashpoint above 100ºF (38ºC).

Thank you for your purchase!

Thank you for purchasing the Wagner FLEXiO sprayer with best-in-class features 

that are designed for spraying residential paint, un-thinned, indoors or out.  

Only the FLEXiO sprayers have the power of the X-Boost® turbine and versatility 

of the iSpray nozzle that will help you finish projects fast and professionally.  

They are easy to use right out of the box and with low overspray and less 

clogging you will enjoy the flexibility to tackle all the painting projects on your 

list.  We appreciate your feedback, so please visit our website and write a review 

on the FLEXiO sprayer so we can continue to learn and improve our products.
Just click on www.wagnerflexio.com

Summary of Contents for flexio 690





















Reviews: