English
5
WARNING! Read all safety warnings and all instructions.
Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Grounding Instructions
This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk
of electric shock by providing an escape wire for the electric current. This product is equipped with a
cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING - Improper installation of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the green grounding wire to
either flat blade terminal. The wire with insulation having a green outer surface with or without yellow
stripes is the grounding wire and must be connected to the grounding pin.
Check with a qualified electrician or serviceman if the grounding instructions are not completely
understood, or if you are in doubt as to whether the product is properly grounded. Do not modify
the plug provided. If the plug will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Grounded outlet
Grounding pin
Cover for grounded outlet box
This product is for use on a nominal 120 volt circuit and
has a grounding plug that looks like the plug as illustrated.
Make sure that the product is connected to an outlet having
the same configuration as the plug.
No adapter should be
used with this product.
IMPORTANT
- Use only a 3-wire extension cord that has
a 3-blade grounding plug and a 3-slot receptacle that will
accept the plug on the product. Make sure your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough to carry the current your product will draw. For
lengths less than 50 feet, use a No. 18 AWG extension cord. For lengths more than 50 feet, use a
No. 14 or No. 16 AWG extension cord. An undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
Minimum gauge for extension cords
Cord length (feet)
Voltage
Ampere
rating
range
3 - 4
120V 25-50 100 150 200 250 300 400 500
18
16
14
12
12
10
10
8
Wagner Spray Tech accessory extension cords
recommended:
P/N 0090241
20 foot extension cord
P/N 0090242
35 foot extension cord
Safety Warnings and Instructions - Sanders
•
This power tool is intended to function as a sander. Read all safety warnings,
instructions, illustrations and specifications provided with this power tool.
Failure to
follow all instructions listed below may result in electric shock, fire and/or serious injury.
•
Operations such as grinding, wire brushing, polishing or cutting-off are not
recommended to be performed with this power tool.
Operations for which the power tool
was not designed may create a hazard and cause personal injury.
•
do not use accessories which are not specifically designed and recommended by the
tool manufacturer.
Just because the accessory can be attached to your power tool, it does
not assure safe operation.
•
The rated speed of the accessory must be at least equal to the maximum speed marked
on the power tool.
Accessories running faster than their rated speed can break and fly apart.
•
The outside diameter and the thickness of your accessory must be within the capacity
rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or
controlled.
•
The arbor size of wheels, flanges, backing pads, or any other accessory must properly
fit the spindle of the power tool.
Accessories with arbor holes that do not match the
mounting hardware of the power tool will run out of balance, vibrate excessively and may
cause loss of control.
•
do not use a damaged accessory. Before each use inspect the accessory such as
abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect
for damage or install an undamaged accessory. After inspecting and installing an
accessory and run the power tool at maximum no-load speed for one minute.
Damaged
accessories will normally break apart during this test time.
