WAGNER Project 115 0418A, Owner'S Manual

13

 Wagner Project 115 - 0418A - Safety Information

Take proper care of your tools. Check whether the moving 

e) 

parts function trouble-free and do not jam, whether 

parts are broken or damaged so that the tool function is 

impaired. 

Have damaged parts repaired before using the tool. 

Many accidents have their origin in power tools that have been 

maintained badly.

Use the power tool, accessories, insert tools, etc. in 

f) 

accordance with these instructions and in a fashion 

specified for this special tool type. Take the working 

conditions and the activity to be carried out into 

consideration. 

The use of power tools for purposes other than the 

intended ones can lead to dangerous situations.

5.  Service

Have your tool repaired only by qualified specialist 

a) 

personnel and only with original spare parts. 

This ensures 

that the tool safety is maintained.

If the supply cord is damaged, it must be replaced by the 

b) 

manufacturer or it’s service agent or a similarly qualified 

person in order to avoid a safety hazard.

For secure handling of Airless high-pressure spraying units the 

following safety regulations are to be observed:

U

Health protection

Danger

Caution!

 Wear breathing equipment: Paint mist and 

solvent vapors are damaging to health. Always wear 

breathing equipment and only work in well ventilated 

rooms or using supplementary ventilating equipment. 

It is advisable to wear working clothing, safty glasses, 
ear protection and gloves

U

  Flash point

Danger

Only use coating materials with a flash point of 21 °C 

or above without additional heating.
The flash point is the lowest temperature at which 

vapors develop from the coating material.
These vapors are sufficient to form an inflammable 

mixture over the air above the coating material.

U

  Explosion protection

Danger

Do not use the unit in work places which are covered 

to the explosion protection regulations. 

U

  Danger of explosion and fire through 

sources of flame during spraying work

Danger

There may be no sources of flame such as, for 

example, open fires, smoking of cigarettes, cigars or 

tobacco pipes, sparks, glowing wires, hot surfaces, 

etc. in the vicinity.

U

  Electrostatic charging (formation of 

sparks or flame)

Danger

Under certain circumstances, electrostatic charging 

can occur on the unit due to the rate of flow of the 

coating material when spraying. On discharging this 

can result in the emergence of sparks or fire. It is 

therefore necessary that the unit is always earthed through the 

electrical installation. The connection must take place through a 

correctly earthed two-pole-and-earth socket outlet.

U

Ventilation

Good natural or artificial ventilation must be ensured in order to 

avoid the risk of explosion or fire and damage to health during spray 

work. 

U

Secure device and spray gun

All hoses, fittings, and filter parts must be secured before 

operating spray pump.  Unsecured parts can eject at great force 

or leak a high pressure fluid stream causing severe injury.
Always secure the spray gun when mounting or dismounting the 

tip and in case of interruption to work.

U

  Recoil of spray gun

Danger

In case of high operating pressure, pulling the 

trigger can effect a recoil force of up to 15 N.
If you are not prepared for this, your hand can be 

thrust backwards or your balance lost. This can lead 

to injury.
Continuous stress from this recoil can cause 

permanent damage to health.

U

  Max. operating pressure

Max. permissible operating pressure for spray gun, spray gun 

accessories and high-pressure hose may not fall short of the 

maximum operating pressure of 200 bar (20 MPa) stated on the 

unit.

U

  Coating substance

Caution against dangers that can arise from the sprayed substance 

and observe the text and information on the containers or the 

specifications given by the substance manufacturer. 

Do not spray any liquid of unknown hazard potential.

U

  High-pressure hose (safety note)

Electrostatic charging of spray guns and the high-pressure hose 

is discharged through the high-pressure hose. For this reason the 

electric resistance between the connections of the high-pressure 

hose must be equal or lower than 197 kΩ/m (60 kΩ/ft.). 

i

For reasons of function, safety and durability, only 

use genuine WAGNER high-pressure hoses and spray 

nozzles. For overview see „Spare parts lists“.

U

Connecting the device

A properly earthed socket outlet with earthing contact must be 

used for connection. The connection must be equipped with a 

residual current protective device with INF ≤ 30 mA.

U

  Setting up the unit

When working indoors:

Danger

Vapors containing solvents may not be allowed to 

build up in the area of the device.
Setting up the unit on the side a way from the sprayed 

object.
A minimum distance of 5 m between the unit and spray 

gun is to be maintained.