ProSpray 3.25
17
D
Anhang
12.
Anhang
12.1
Düsenauswahl
6NFJOFFJOXBOEGSFJFVOESBUJPOFMMF"SCFJUTXFJTF[VFS[JFMFOJTUEJF"VTXBIMEFS%ÛTFWPOHSPFS8JDIUJHLFJU
In vielen Fällen kann die richtige Düse nur über einen Spritzversuch ermittelt werden.
Einige Regeln hierzu:
Der Spritzstrahl muss gleichmäßig sein.
Wenn Streifen im Spritzstrahl erscheinen, so ist der Spritzdruck zu geri
ng oder die Viskosität des Beschichtungs-stoffes zu hoch.
Abhilfe
: Druck erhöhen oder Beschichtungsstoff verdünnen. Jede Pumpe leistet eine bestimmte Fördermenge im Verhältnis zur Düsengröße:
Es gilt grundsätzlich:
Große Düse = niedriger Druck
Kleine Düse = hoher Druck
Es gibt ein großes Sortiment von Düsen mit verschiedenen Spritzwinkeln.
12.2
Wartung und Reinigung von Airless Hartmetall-Düsen
Standarddüsen
Ist eine andere Düsenausführung montiert, dann nach Herstellerangaben reinigen.
%JF%ÛTFIBUFJOFNJUHSÕUFS1SÅ[JTJPOCFBSCFJUFUF#PISVOH6NFJOFMBOHF-FCFOTEBVFS[VFSSFJDIFOJTUFJOFTDIPOFOEF#FIBOEMVOH
FSGPSEFSMJDI%FOLFO4JFEBSBOEBTTEFS)BSUNFUBMMFJOTBU[TQSÕEFJTU%ÛTFOJFNBMTXFSGFOPEFSNJUTDIBSGFONFUBMMFOFO(FHFOTUÅOEFO
bearbeiten.
Folgende Punkte sind zu beachten, um die Düse sauber und einsatzbereit zu halten:
&OUMBTUVOHTWFOUJMÕíOFO7FOUJMTUFMMVOH13*.&
k
Zirkulation).
2. Gerät ausschalten.
3. Düse von der Spritzpistole demontieren.
4. Düse in ein entsprechendes Reinigungsmittel legen bis alle Beschichtungsstoffreste aufgelöst sind.
5. Wenn Druckluft vorhanden ist, Düse ausblasen.
.JUFJOFNTQJU[FOIÕM[FSOFO4UBC ;BIOTUPDIFSFWFOUVFMMF3FTUFFOUGFSOFO
7. Die Düse unter Zuhilfenahme eines Vergrößerungsglases kontrollieren und falls erforderlich, Punkt 4 bis 6 wiederholen.
12.3
Spritzpistolen-Zubehör
Flachstrahl-Verstelldüse
CJTCBS .1B
Berührungsschutz
zur Flachstrahl-Verstelldüse
#FTUFMM/S
0097 294
Düsenverlängerung mit
schwenkbarem
Kniegelenk
(ohne Düse)
Düsenverlängerung
Länge: 100 cm
#FTUFMM/S
0096 015
Länge: 200 cm
#FTUFMM/S
0096 016
Länge: 300 cm
#FTUFMM/S
0096 017
DN'(FXJOEF#FTUFMM/S
0556 051
DN((FXJOEF#FTUFMM/S
0556 074
DN'(FXJOEF#FTUFMM/S
0556 052
DN((FXJOEF#FTUFMM/S
0556 075
DN'(FXJOEF#FTUFMM/S
0556 053
DN((FXJOEF#FTUFMM/S
0556 076
DN'(FXJOEF#FTUFMM/S
0556 054
DN((FXJOEF#FTUFMM/S
0556 077
Düsen-
markierung
Bohrung
mm
Spritzbreite bei etwa 30 cm
Entfernung vom Spritzobjekt
Druck 100 bar (10 MPa)
Verwendung
Flachstrahl-
Verstelldüse
Bestell-Nr
15
0,13 - 0,46
5 - 35 cm
Lacke
0999 057
20
0,18 - 0,48
5 - 50 cm
Lacke, Füller
0999 053
28
0,28 - 0,66
8 - 55 cm
Lacke, Dispersionen
0999 054
41
0,43 - 0,88
10 - 60 cm
Lacke, Dispersionen
Rostschutzfarben -
0999 055
49
0,53 - 1,37
10 - 40 cm
Großflächen-anstriche
0999 056