background image

LIMITED WARRANTY

ELECTROSTATIC PAINT SPRAY EQUIPMENT

To validate this warranty, the completed registration card must be mailed within one week of the date of purchase to Wagner Spray
Tech Corporation.

Wagner Spray Tech Corporation extends to the original purchaser of its electrostatic paint spray equipment a one year warranty
against defects in material or workmanship provided that the equipment is installed and operated in accordance with the
recommendations and instructions of Wagner Spray Tech Corporation. Wagner Spray Tech will repair or replace, at its option,
defective parts without charge if such parts are returned with transportation charges prepaid to the nearest authorized service
agency or to Wagner Spray Tech Corporation, 1770 Fernbrook Lane, Minneapolis, Minnesota.

This warranty does not cover:

1.

 Equipment and accessories supplied to Wagner Spray Tech Corporation by other manufacturers including hose are covered
by the express warranties of the original manufacturers. Wagner Spray Tech Corporation will provide the purchaser with
 reasonable information and assistance in making claims to the original manufacturers under their warranty.

2.

Normal wear and/or defects caused by or related to abrasion, corrosion, abuse, negligence, accident faulty installation or
 tampering in a manner which impairs normal operation.

3.

Transportation costs and other incidental, direct, special or consequential damages or loss.

Any implied warranty of merchantability or fitness for a particular purpose on Wagner Spray Tech Corporation’s spray equipment
is limited in duration to the duration of this warranty.

Some states do not allow the exclusion of incidental or consequential damages, or allow limitations on how long an implied warranty
lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.

Copyright 1989 by Wagner Spray Tech Corporation

ALL RIGHTS RESERVED

R

Wagner Spray Tech Corporation
1770 Fernbrook Lane
Minneapolis, Minnesota 55447
Telephone (612) 553-7000

PRINTED IN U.S.A.

U.S. PATENT 3,843,052

20

Summary of Contents for Stati-Kit 2000 0292003





















Reviews: