background image

5

 

Super Finish 33 PLUS/PRO • Nespray Pro

1.9 

MAX. OPERATING PRESSURE

The permissible operating pressure for the spray gun, spray 

gun accessories, unit accessories and high-pressure hose 

must not fall short of the maximum operating pressure of 25 

MPa (250 bar or 3625 psi).

1.10 

HIGH-PRESSURE HOSE

Attention, danger of injury by injection! Wear 

and tear and kinks as well as usage that is not 

appropriate to the purpose of the device can 

cause leakages to form in the high-pressure 

hose. Liquid can be injected into the skin 

through a leakage.

  High-pressure hoses must be checked thoroughly before 

they are used.

  Replace any damaged high-pressure hose immediately.

  Never repair defective high-pressure hoses yourself!

  Avoid sharp bends and folds: the smallest bending radius 

is about 20 cm.

 Do 

not drive over

 the high-pressure hose. Protect against 

sharp objects and edges.

  Never pull on the high-pressure hose to move the device.

  Do not twist the high-pressure hose.

  Do not put the high-pressure hose into solvents. Use only 

a wet cloth to wipe down the outside of the hose.

  Lay the high-pressure hose in such a way as to ensure that 

it cannot be tripped over.

Only use WAGNER original-high-pressure 

hoses in order to ensure functionality, safety 

and durability.

1.11 

ELECTROSTATIC CHARGING (FORMATION OF 

SPARKS OR FLAMES) 

Electrostatic charging of the unit may occur 

during spraying due to the flow speed of 

the coating material. These can cause sparks 

and flames upon discharge. The unit must 

therefore always be earthed via the electrical 

system. The unit must be connected to an 

appropriately-grounded safety outlet.

An electrostatic charging of spray guns and the high-pressure 

hose is discharged through the high-pressure hose. For this 

reason the electric resistance between the connections of the 

high-pressure hose must be equal to or lower than 1 MΩ.

1.12 

USE OF UNITS ON BUILDING SITES AND 

WORKSHOPS

The unit may only be connected to the mains network via a 

special feeding point with a residual-current device with INF 

≤ 30 mA. An upstream circuit breaker (fuse) with 16 A (B or C 

characteristics) is required.

1.14 

VENTILATION WHEN SPRAYING IN ROOMS

Adequate ventilation to ensure removal of the solvent vapors 

has to be ensured.

1.15 

SUCTION INSTALLATIONS

The are to be provided by the unit user in accordance with the 

corresponding local regulations.

1.16 

EARTHING OF THE OBJECT

The object to be coated must be earthed.

(Building walls are usually earthed naturally)

1.17 

CLEANING THE UNIT WITH SOLVENTS

When cleaning the unit with solvents, the 

solvent should never be sprayed or pumped 

back into a container with a small opening 

(bunghole). An explosive gas/air mixture can 

arise. Only use an earthed container made 

from metal.

1.18 

CLEANING THE UNIT

Danger of short-circuits caused by water in-

gression!

Never spray down the unit with high-pres-

sure or high-pressure steam cleaners.

1.19 

WORK OR REPAIRS AT THE ELECTRICAL 

EQUIPMENT

These may only be carried out by a skilled electrician. No liabil-

ity is assumed for incorrect installation.

1.13 

SOCKET AT THE UNIT (ONLY SF33 PLUS)

Do not load the socket with more than 1200 Watt. Unroll

any connected cable drum completely.

1.20 

WORK AT ELECTRICAL COMPONENTS

Unplug the power plug from the outlet before carrying out 

any repair work.

GB

Summary of Contents for Super Finish 33 PLUS




















































Reviews: