background image

122  Diagnostics 

WAGO-I/O-System 750 

 

 

750-370 PROFINET IO Fieldbus Coupler 

 

Manual 

 

Version 2.0.0  

Table 57: Blink Code Table for the I/O LED Signaling, Error Code 3 

Error code 3: “Protocol error, internal bus” 
Error 

Argument 

Error Description  Solution 

Internal data bus 

communication is 

faulty, defective 

module cannot be 

identified. 

- Are passive power supply modules (750-613) located in the 

node? - 

1.  Check that these modules are supplied correctly with 

power. 

2.  Determine this by the state of the associated status LEDs.  

 

- Are all modules connected correctly or are there any  

750-613 Modules in the node? - 

1.  Determine the faulty I/O module by turning off the power 

supply. 

2.  Plug the end module into the middle of the node.  

3.  Turn the power supply on again. 

4.  - LED continues to flash? - 

Turn off the power supply and plug the end module into 

the middle of the first half of the node (toward the 

fieldbus coupler). 

- LED not flashing? - 

Turn off the power and plug the end module into the 

middle of the second half of the node (away from the 

fieldbus coupler). 

5.  Turn the power supply on again. 

6.  Repeat the procedure described in step 4 while halving 

the step size until the faulty I/O module is detected. 

7.  Replace the faulty I/O module. 

8.  If there is only one I/O module on the fieldbus coupler 

and the LED is flashing, either the I/O module or fieldbus 

coupler is defective. Replace the I/O module with a 

pretested, properly functioning I/O module. If the LED 

no longer flashes, the replaced I/O module was faulty. 

Replace this I/O module. 

9.  If the LED continues to flash, the fieldbus coupler is 

faulty. Replace the fieldbus coupler. 

 

Summary of Contents for 750-370































































































































































































































Reviews: