background image

36 

System Description 

WAGO-I/O-System 750 

 

 

750-370 PROFINET IO Fieldbus Coupler 

 

Manual 

 

Version 2.0.0  

Pos: 18.15.40 /Seri e 750 ( WAGO-I/O-SYSTEM)/Systembeschr eibung/Versorgung/Netzger äte @ 3\mod_1232950093484_21.docx @ 26728  @  3 @ 1 

 

3.6.6 

Power Supply Unit 

The WAGO-I/O-SYSTEM 750 requires a 24 VDC voltage (system supply). 

 

 

 

Recommendation 

A stable power supply cannot always be assumed everywhere. Therefore, you 

should use regulated power supplies to ensure the quality of the supply voltage 

(see also table “WAGO power supply units”). 

For brief voltage dips, a buffer (200 µF per 1 A load current) must be provided. 

 

 

 

Power failure time not acc. IEC 61131-2! 

Note that the power failure time of 10 ms acc. IEC 61131-2 is not maintained in a 

maximum configuration. 

The power demand must be determined individually depending on the entry point 

of the field supply. All loads through field devices and I/O modules must be taken 

into account. The field supply also impacts the I/O modules because the input and 

output drivers of some I/O modules require the voltage of the field supply. 

 

 

 

System and field supply must be isolated! 

The system supply and field supply must be isolated to ensure bus operation in the 

event of short circuits on the actuator side. 

 

 

Pos: 18.15.41 /D okumentation allgemein/Gliederungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @  @ 1 

 

 

 

Table 10: WAGO Power Supply Units (Selection) 

WAGO Power 

Supply Unit 

Description 

787-612 

Primary switched mode;  

DC 24 V; 2,5 A Input nominal voltage AC 230 V 

787-622 

Primary switched mode;  

DC 24 V; 5 A Input nominal voltage AC 230 V 

787-632 

Primary switched mode;  

DC 24 V; 10 A Input nominal voltage AC 230/115 V 

 

Rail-mounted modules with universal mounting carrier  

288-809 

AC 115 V/DC 24 V; 0,5 A 

288-810 

AC 230 V/DC 24 V; 0,5 A 

288-812 

AC 230 V/DC 24 V; 2 A 

288-813 

AC 115 V/DC 24 V; 2 A 

Summary of Contents for 750-370































































































































































































































Reviews: