background image

WAGO-I/O-System 750 

Device Description 

55 

750-370 PROFINET IO Fieldbus Coupler 

 

 

Manual 

 

Version 2.0.0  

 

Pos: 40 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebeschreibung/Technische Daten - Ü berschrift 2 @ 3\mod_1232967587687_21.docx @ 26924  @ 2 @ 1 

 

4.6 

Technical Data 

Pos: 41 /Serie 750 ( WAGO-I/O-SYST EM)/Ger ätebeschrei bung/T echnische Daten/F el dbuskoppl er/-contr oller/T echnische D aten 750- 0370  @ 22\mod_1429611431730_21.docx @ 180808 @ 3333 @ 1 

 

4.6.1 

Device Data 

Table 21: Technical Data – Device Data  

Width 

51 mm 

Height (from upper edge of DIN 35 

rail) 

65 mm 

Length 

100 mm 

Weight 

189,5 g 

Degree of protection 

IP 20 

Fieldbus 

 

Max. input process image 

 

Max. output process image 

 

256 bytes 

256 bytes 

Number of I/O modules 

 

with bus extension 

128 

Configuration  

via PC 

PROFINET IO features 

Integrated 2-port switch; 

Auto-negotiation, Auto-MDIX; 

Send clock: 1 ms (RT); 

Send cycle

s ≥ 4 ms;

 

Device replacement without programming 

tool 

Protocols 

PROFINET IO (RT Class 1) 

Conformance Class B (DCP, SNMP, 

LLDP) 

HTTP 

Profiles supported 

PROFIsafe V2.4, iPar-Server V1.0.1 

ID code 

Vendor-ID: 0x011D; 

Device-ID: 0x02EE; 

Module-ID:  actual 0x02060172 

 

Summary of Contents for 750-370































































































































































































































Reviews: