18 Device Description
WAGO-I/O-SYSTEM 750 XTR
750-630/040-001 SSI Interface Adjust XTR
Manual
Version 1.1.0
Pos: 18.11 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung (alte Struktur)/Anschl üsse/Lei stungskontakte/Fel dversorgung - Ü berschrift 3 @ 6\mod_1256294692864_21.docx @ 43664 @ 3 @ 1
3.2.2
Power Jumper Contacts/Field Supply
Pos: 18.12.1 /Serie 750 ( WAGO-I/O- SYST EM)/Wichtig e Erl äuter ung en (alte Struktur)/Sicher heits- und sonstige Hi nweise/Vorsicht/Vorsicht: Verletzungsgefahr durch scharfkantige Messer kontakte! @ 6\mod_1256193279401_21.docx @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury. Do not touch the blade contacts.
Pos: 18.12.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung ( alte Struktur)/Anschl üsse/Leistungskontakte 2 LK (Messer /Feder) - Ei nleitung @ 15\mod_1371721641099_21.docx @ 123714 @ @ 1
The I/O module 750-630/040-001 has 2 self-cleaning power jumper contacts that
supply and transmit power for the field side. The contacts on the left side of the
I/O module are designed as blade contacts and those on the right side as spring
contacts.
Pos: 18.12.3 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung ( alte Struktur)/Anschl üsse/Leistungskontakte 2 LK (Messer /Feder) - Abbil dung, einfache Breite - Standard @ 15\mod_1367500700037_21.docx @ 118396 @ @ 1
Figure 3: Power Jumper Contacts
Pos: 18.12.4 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung ( alte Struktur)/Anschl üsse/Leistungskontakte 2 LK (Messer /Feder) - Legende @ 15\mod_1371721352500_21.docx @ 123710 @ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact Potential transmission (U
v
) for field supply
2
Spring contact Potential transmission (0 V) for field supply
3
Blade contact Potential feed-in (0 V) for field supply
4
Blade contact Potential feed-in (U
v
) for field supply
Pos: 18.12.5 /Serie 750 ( WAGO-I/O- SYST EM)/Wichtig e Erl äuter ung en (alte Struktur)/Sicher heits- und sonstige Hi nweise/Achtung/Achtung: M axi maler Str om Leistungskontakte 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.
Pos: 18.13 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
