Middle
1. No attachments needed.
Start with the sideburns.
2. Continue around ear as
shown.
4. Trim neckline as shown.
When you want to blend from one section to the next, you will need to practice moving the
clipper in an upward rocking motion. This motion will leave the hair slightly longer where the
clipper pulls away from the scalp, enabling you to blend between the sections and achieve
a smooth transition from one length of hair to the next. This technique will enhance the
appearance of your haircuts.
1. Blend out any cut lines.
Lines may form where you
change guard sizes. Use the
same comb used in
step 3
3. Using the guard used in
step 8
repeat blending the
top outline as needed.
2. Using a rocking motion,
blend out the middle cut
line.
OUTLINING
BLENDING
Clipper Blades
(Removable)
On/Off Switch
Cord Strain Relief
Power Cord
Home
Haircutting
fig. A
fig. A
fig. B
fig. B
Please register your Wahl Clipper online at: grooming.wahl.com
Purchase Confirmation-
With the information you provide, we confirm the date of purchase of your product. This
confirmation is of benefit to you, especially if your original proof of purchase is lost.
Proof of Ownership-
Your UPC number, item number and other information will be kept in our files for up to ten
years.
1
2
3
4
1. Comb hair and remove tangles.
Attach the largest attachment guard to
the clipper.
2. Start at hairline on side of head
and cut up to middle of head.
Note:
If cut hair is too long repeat
with next smaller guard.
3. Continue around head repeating step 2.
4. You are now ready to cut
the middle portion of the hair.
7
8
5
6
5. Use the attachment guards with the
next highest number than in step 3.
Example:If you used a #6 guards in
step 3
, select guard #7.
6. Continue cutting around middle
portion of head as in steps 2 and 3.
7. For cutting top of head, use the
attachment guard with the next highest
number than in
step 6
. Start at front
bang area.
8. Cut across top of head. Comb hair
on entire head to assess if further
cutting is necessary.
To achieve a “tapered” cut around the ears, use the left and right tapered
attachment guards
1) Attach the “R” RIGHT attachment guard to the clipper.
fig. A) First, starting behind the RIGHT ear (so shorter portion of guard fingers are closest
to the ear), move the clipper upward and around towards the front side of the ear. Repeat as
needed.
fig B) Second, starting on the front of the LEFT ear, (so shorter portion of guard fingers are
closest to the ear), move the clipper upward and around towards the back side of the ear.
Repeat as needed.
2) Repeat, except now using the “L” LEFT guard. Attach the “L” LEFT attachment guard to
the clipper.
fig. A) First, starting behind the LEFT ear (so shorter portion of guard fingers
are closest to the ear), move the clipper upward and around towards the front side
of the ear. Repeat as needed.
fig. B) Second, starting on the front of the RIGHT ear, (so shorter portion of guard fingers
are closest to the ear), move the clipper upward and around towards the back side of the
ear. Repeat as needed.
DETACHABLE BLADES
STEP-BY-STEP GUIDE FOR CUTTING HAIR
TIPS & TECHNIQUES
EARS
EASY-TO-USE ATTACHMENT GUARDS
CLIPPER MAINTENANCE
The blades on your new Wahl clipper are detachable for easy cleaning. The clipper blades were
oiled and aligned before leaving our factory. Don’t attempt to adjust blade alignment. Please
contact our Customer Service Department if any questions.
REMOVING BLADES:
Before removing blades, make sure the on/off switch is turned to the “0” or “OFF” position.
1. Hold the clipper in both hands. Using both thumbs, push the blades away from the front
of the clipper.
2. The blade set with the top and bottom blades will come off in one piece.
OIL
The blades on your new clipper should be oiled every few haircuts. Place a few drops of
Wahl Clipper Oil on the teeth (front) as well as at the back side of the blade. Use only Wahl
Clipper oil (a small bottle is included in this kit, additional oil can be purchased separately,
see www.grooming. Wahl.com for details).
DO NOT USE HAIR OIL, GREASE,
OR ANY OIL MIXED WITH KEROSENE OR ANY SOLVENT.
ATTACHING BLADES:
Before reattaching blades, make sure the on/off switch is turned to the “0” or “OFF” position.
1. Place the blade at an angle (with the bottom portion of blade fitting into the clipper) so the
outer white clips of the blade set sit just below the metal clips inside the clipper. Make
sure blade is center aligned with clipper.
2. While holding the bottom of the blade, push-on the blade to the clipper with your thumb
until blade “snaps” into place. Don’t use excessive force to push blade into place.
CORD
The cord should not be used to pull the clipper. Since freedom of movement needs to be
maintained, care should be used to keep the cord untwisted and unobstructed.
YOUR CLIPPER HAS A POLARIZED PLUG:
To reduce the risk of electric
shock, this appliance has a polarized plug (one plug blade is wider than the other). This
plug fits in a polarized outlet only one way. In the event the plug doesn’t fit fully in the outlet,
reverse the plug.
DO NOT CHANGE THE PLUG IN ANY WAY.
CLEANING:
To remove hair from between the blades, use the cleaning brush provided.
DO NOT USE
WATER TO CLEAN THE BLADES.
For best results, after brush cleaning the
blades, add Wahl clipper oil to the blades.
Center Align Blade
When you cut your hair, you should visualize the head as if it were divided
into four sections. Image below shows the different sections. Using proper
techniques when moving from one section to the next will help you blend the
sections together for professional looking results.
• The first time you cut hair, cut only a small amount of hair until you become
accustomed to the length of hair each attachment guard provides.
• For best results, hair should be dry before using clipper.
• For best results, when cutting hair, go through hair at a slow, even speed.
Don’t force the clipper through the hair.
• For best results, go through the hair against the direction of your hair’s growth,
so you can catch more hair with the guard.
• The blades on your new clipper should be oiled every few haircuts.
grooming.wahl.com
Question?
For personal attention from one of our customer service
representatives please contact us at:
www.grooming.wahl.com
or
1-800-767-9245
© 2016 WAHL CLIPPER CORPORATION
P.O. Box 578, Sterling, Illinois 61081 USA
BATTERY INSTRUCTIONS
Select clipper kits include a battery trimmer, your kit may or may not include a trimmer
1. Remove battery cover from clipper by pushing in and back on the plastic door in the direction of the
arrow.
2. IMPORTANT: Be sure to insert the negative (-) end of each battery first, so that it depresses the spring at
the top of the battery compartment. Then slide the positive (+) end into position. Do not allow the
negative terminal clips to bend and cut the casing of the batteries.
Use alkaline batteries with your Wahl Clipper. Alkaline batteries will provide the longest operating time
before battery replacement is needed. Clipper should run approximately three hours on alkaline batteries.
3. Replace battery cover to its original position.
4. Move switch to “ON” position to use.
5. To maximize battery life, trimmer should be shut “OFF” immediately after using.
WARRANTY
YOUR NEW CLIPPER
YOUR NEW BATTERY TRIMMER
5-YEAR LIMITED WARRANTY - CLIPPER
Valid in U.S.A. Only
If your Wahl product fails to operate satisfactorily within five (5) years from the date of original purchase
or receipt as a gift, Wahl will, at our option, repair or replace it and return it to you FREE OF CHARGE.
2-YEAR LIMITED WARRANTY - BATTERY TRIMMER
Valid in U.S.A. Only
Not all kits include a trimmer
If your Wahl product fails to operate satisfactorily within two (2) years from the date of original purchase
or receipt as a gift, Wahl will, at our option, repair or replace it and return it to you FREE OF CHARGE.
Do not return this product to store where purchased.
Products needing repair under this warranty
should be returned with postage prepaid to:
Wahl Clipper Corp.
Attn: Repair Department
3001 Locust Street
Sterling, Illinois 61081
Include a note describing the defect and the date of original purchase or receipt as a gift (if in warranty).
Products out of warranty will be repaired at our standard repair charges.
This warranty is void and no repair or replacement will be made under this warranty or otherwise if:
(1) The product is modified in any manner or repaired by anyone other than Wahl Clipper Corporation
or Wahl authorized service center. (2) The product has been used commercially or subjected to
unreasonable use.
This warranty gives you specific legal rights and you may also have other rights which may vary from
state to state. No other written express warranty is given. Any implied warranty, including any warranty
of merchantability which may arise from purchase or use, is limited to the year period provided in this
express warranty. Some states may not allow such limitation, so it may not apply to you. No responsibility
is assumed for incidental or consequential damages of any type, or for the use of unauthorized
attachments. Some states may not allow the exclusion or limitation of incidental or consequential
damages, so the limitation or exclusion may not apply to you. Outside U.S.A., check with store for Wahl
authorized distributor’s warranty.
BROW TRIM
GUARDS
EAR TRIM GUARDS
1. Attach the brow trim guard
to clipper
2. Starting from just above
your nose, slowly guide
the clipper to the outside of
your face.
For shorter brow trim
repeat steps 1 and 2
working from outside
face to your nose.
1. Attach ear trim guard to
clipper.
2. Hold the clipper at a
45-degree angle.
3. Use your finger to tilt ear
forward away from hairline.
4. Slowly trim along the hair
line from back to front.
Avoid poking eyes.
NOTE:
NOT ALL WAHL KITS INCLUDE BROW / EAR TRIM GUARDS
Some kits do not include all size Wahl guards. Some kits include colored guards.
#
1
/
2
-
(1.5
mm
)
1
/
16
”
#
1
-
(3
mm
)
1
/
8
”
#
1
1
/
2
-
(4.5
mm
)
3
/
16
”
#
2
-
(6
mm
)
1
/
4
”
#
3
-
(10
mm
)
3
/
8
”
#
4
-
(13
mm
)
1
/
2
”
#
5
-
(16
mm
)
5
/
8
”
#
6
-
(19
mm
)
3
/
4
”
#
7
-
(22
mm
)
7
/
8
”
#
8
-
(25
mm
) 1”
#
10
-
(32
mm
) 1
1
/
4
”
#
12
-
(38
mm
) 1
1
/
2
”
Right Ear Taper
Left Ear Taper
• Attachment guards help you cut
hair to a desired length by keeping
the blades at set distance from the
skin helping ensure an even hair
length when cutting hair with a
clipper. For reference, each guard
is numbered and also lists what the
length of the hair will be after being
cut.
• Attachment guard sizes vary.
Always start with a longer length
guard (you can always use a
shorter length guard if the length is
not short enough).
• The first time you cut hair, cut
only a small amount of hair until
you become accustomed to the
length of hair each attachment
guard provides.
Part #91592
v.2017.02
ADDING GUARDS: Pictured in fig A & fig B
Before adding guards, make sure the on/off switch is turned to the “0” or “OFF” position.
1. While holding at a slight angle, place the attachment guard onto the clipper so the tips of the blade
rests into the slots of the guard fingers. (fig A)
2. Using your thumb, push down on the guard, where the guard size number is located, until you hear a
“SNAP”. (fig B)
REMOVING GUARDS: Pictured in fig C
Before removing guards, make sure the on/off switch is turned to the “0” or “OFF” position.
1. While holding the top of attachment guard, place your thumb on the underside of the attachment guard
tab. Push up on tab to remove guard from clipper. (fig C)
(fig A)
(fig B)
Push Down
Push Up
(fig C)
Section 2:
Under the rim
of the head
Section 4:
Top of
the head
Section 1:
The neckline
Section 3:
The rim
or side
