5
CHROMSTYLE CLIPPER INSTRUCTIONS
•After the appliance has been removed from the charging stand, the display goes out after approx. 30 seconds (power saving mode).
•It should take around 60 minutes for the appliance to charge to full capacity.
5. Once the battery is fully charged, a signal will sound.
BATTERY OPERATION
1. Switch on the appliance using the on/off switch and switch off after use (Fig. 3a/b).
•After the appliance has been switched off, the display goes out about 30 seconds later (power saving mode).
•When the battery is fully charged, the appliance can be used for up to 90 minutes without mains connection.
•The charge status of the battery is displayed by the battery power indicator (C).
•When the battery has fully run down, the appliance switches itself off automatically.
•In case of insufficient maintenance of the blade set, the operating time can be reduced considerably.
MAINS OPERATION
1. Connect the appliance plug (M) on the plug-in transformer to the appliance socket (F) (Fig. 2a).
2. Connect the plug-in transformer to the mains socket (Fig. 2b).
3. Switch on the appliance using the on/off switch and switch off after use (Fig. 3a/b).
SETTING THE CUTTING LENGTH
The cutting length can be adjusted to between 0.7mm and 3mm (5 possible positions) using the cutting-length adjustment integrated into the blade set (Fig. 5).
CUTTING WITH THE ATTACHMENT COMB
The appliance can also be operated with attachment combs. In order to achieve the indicated cutting length, the cutting length adjustment lever should be set
to position 1 (Fig. 5).
The following attachment combs are included as standard: 3 mm, 6 mm, 9 mm and 12 mm cutting lengths.
ATTACHING/REMOVING THE ATTACHMENT COMB
1. Slide the attachment comb on to the blade set in the direction of the arrow until it reaches the limit stop (Fig. 6a).
2. The attachment comb can be removed by pushing it in the direction of the arrow (Fig. 6b).
CARE AND CLEANING
Danger! Electric shock due to penetration of liquid.
►
Switch the appliance off and disconnect from the power supply, before you start with cleaning and care.
►
Do not immerse the appliance in water!
►
Do not allow any liquid to get inside the appliance.
►
Only reconnect the appliance to the power supply if it is completely dry.
Handle with care! Danger from aggressive chemicals.
Aggressive chemicals could damage the appliance and accessories.
►
Never use solvents or scouring agents.
►
Only use cleaning agents and blade set oil recommended by the manufacturer.
Hygienic spray and blade oil are available from your wholesaler or direct from our customer service.
Remove the attachment comb (Fig. 6b) after every use and lift the blade set out of the housing (Fig. 7a). Use the cleaning brush to remove any cut hairs from
the housing opening and from the blade set (Fig. 8). The cleaning lever can also be pressed. This allows the cut hairs that accumulate between the bottom
blade and the top blade to be easily removed using the cleaning brush (EASY CLEANING).
Only wipe the appliance with a soft, slightly damp cloth.
The blade set can be cleaned by using the hygienic spray.
Oil the blade set with the blade set oil (Fig. 9).
For a good and long-lasting cutting performance, it is important to oil the blade set frequently. If the cutting performance deteriorates after long use despite
regular cleaning and oiling, the blade set should be replaced.
AUTOMATIC SENSOR SYSTEM
To give you advance notice of an urgent need for maintenance care, your hair cutting appliance has been equipped with an automatic sensor system.
The sensor system automatically recognises when the blade set needs oiling or cleaning. After the appliance is switched off, an acoustic signal will sound and
the battery power indicator will flash for 2 minutes. The acoustic signal and the flashing of the battery power indicator can be cancelled (turned off) by briefly
switching the appliance on and off.
Before using the appliance again, it is strongly recommended to clean the appliance and oil the blade set.
Failure to observe these instructions may result in damage to and early failure of the appliance, which will void all guarantee claims.
CHANGING THE BLADE SET
Warning! Injuries and material damage due to incorrect handling.
►
Switch the appliance off and disconnect from the power supply before changing the blade set.
1. Switch the appliance off using the on/off switch (Fig. 3b) and disconnect from the power supply.
2. Slide the blade set off the housing in the direction of the arrow (Fig. 7a). Remove the blade set.
3. Replace the blade set by hooking it into the housing and pressing it down until it clicks into position (Fig. 7b).
PROBLEM ELIMINATION
Blade set is cutting badly or pulling hair out.
Cause: Blade set is dirty or worn out.
►
Clean and oil the blade set (Fig. 8/9); if this does not resolve the problem, replace the blade set (Fig. 7).
Battery life is too short.
Carefully clean and oil the blade set (Fig. 8/9). A blade set that is very dirty and has not been oiled can halve the available battery life! If the blade set is clean
and oiled and the battery life is still far too short, it is likely that the batteries are nearing the end of their life.
Battery life generally decreases at a steady rate when the appliance is used on a day-to-day basis. The batteries used here are specially designed for
