Wahlberg 245 Winch 50 User Manual Download

Page: 9 / 15

805.245.005

Date: January 10, 2017

MENU

The menu structure is divided into two different areas for safer motor control.

Control mode

The display shows:

DMX CONTROL .

START CHAN 1

Menu navigation mode

Top Line shows

MENU NAVIGATE

In menu navigate mode, the different parameters can be changed.
In menu navigate mode the motor is stopped and DMX input has no effect, the motor can be moved
by the MAN UP/DWN menu though.

Menu mode change

MENU - NAVIGATE:

The top line of the display is showing:

DMX CONTROL

Push the buttons UP & DOWN and hold them for 3 seconds.

Now the top line of the display should show:

MENU NAVIGATE

MENU - DMX CONTROL:

Go back to the starting position and activate DMX control
The top line of the display is showing:

MENU NAVIGATE

Push the buttons UP & DOWN and hold them for 3 seconds.

Now the top line of the display is showing:

DMX CONTROL

Navigate the menu

The top line of the display is showing:

MENU NAVIGATE

Push the buttons UP or DOWN to go up and down in the menu choices.
The bottom line of the display is showing:

DMX ADDR 1

Adjusting menu parameters

The top line of the display is showing:

MENU NAVIGATE

The bottom line of the display is showing:

DMX ADDR 1

Push ENT to change the DMX ADDR value.
The top line of the display is showing:

EDIT MENU VALUES

The bottom line of the display is showing:

DMX ADDR 1

Save changed value

The top line of the display is showing:

EDIT MENU VALUES

The bottom line of the display is showing:

DMX ADDR 270

Push ENT to change the top line to:

SAVING 1-20

Then press and hold ENT

The top line of the display counts up to 20 then shows OK.

SAVING OK

The Value is now saved in the memory.

Summary of Contents for 245 Winch 50
















Search results

Summary of Contents for 245 Winch 50

Reviews:

Related manuals for 245 Winch 50

Brands by name

Popular brands

Wahlberg 245 Winch 50, User Manual

Search results

Summary of Contents for 245 Winch 50

Reviews:

Related manuals for 245 Winch 50

Brands by name

Popular brands