background image

289.805.003 

14

 

Date: 2018-11-28 

DMX channel overview 

DMX 
channel 

Function 

Description 

Position rough 

This channel controls the position of the Mini Roll Down, with the speed (DMX channel 3). 

This rough position works together with the fine position (DMX channel 2).  

The rough position and the fine position are multiplied in to a 16 bit channel. The rough 
position is the 

MSB

Position fine 

This channel controls the position of the Mini Roll Down, with the speed set on DMX 
channel 3.  

This fine position works together with the rough position (DMX channel 1).  

The fine position and the rough position are multiplied in to a 16 bit channel. The fine 
position is the 

LSB

 

Speed 

This channel controls the speed of the Mini Roll Down. 

This channel defines the maximum speed, and the Mini Roll Down slows down as closing in 
on the wanted position.  

This channel also works as a main brake; the motor does not run unless the channel is set 
above 0%. The speed-channel can also be used to make soft and slow movements or fast 
and sudden movements. 

Enable save 
soft limits 

When channel 4 is between 60-65% saving of soft-limit top and bottom position is enabled.  

The Mini Roll Down can be operated while channel 4 is between 60-65%, however, to 
minimise the risk of accidentally setting new top and bottom limit, channel 4 should be set 
to 0% when not in use. 

Manuel Up / 
Set soft-limit 
top (100% 
position) 

The value of the channel determines the speed at which the Mini Roll Down moves up. This 
channel overrules movement with positioning via channel 1 & 2. 
 

 

Channel 4 

between

 60-65% enable save soft-limits. 

When channel 4 is in this range the top position can be adjusted using channel 5.  
The Top position is saved when channel 5 is put back at 0%. Note that it should be 
moved gradually towards 0% to give the banner time to slow down. 
The top position should be set with channel 5 before the bottom position is set with 
channel 6, since the range is calculated relative to the top position.  
 

 

Channel 4 

not between

 60-65% enable save soft-limits is 

NOT

 enabled. 

When save soft-limits is not enabled, channel 5 can still run the roll up but any position 
is not saved, so it returns to the position given by channel 1 &2. 

Manuel Down 
/ Set soft-limit 
bottom, and 
range (0% 
position) 

The value of the channel determines the speed at which the Mini Roll Down moves up. This 
channel overrules movement with positioning via channel 1 & 2. 
 

 

Channel 4 

between

 60-65% enable save soft-limits. 

When channel 4 is in this range the end position can be adjusted when running with 
channel 6. The bottom position is set when channel 6 is put back at 0%. 
The top position should be set with channel 5 before the bottom position is set with 
channel 6, since the range is calculated relative to the top position.  
 

 

Channel 4 

not between

 60-65% enable save soft-limits is 

NOT

 enabled. 

When save  soft-limits  is not  enabled, channel 5 can still run the  roll down but  any 
position is not saved, so it returns to the position given by channel 1 & 2. 

 

 

Summary of Contents for 289.701


























Reviews: