background image

352-353.805.006 

9

 

Date: 2019-07-02 

Physical installation

 

WARNING! The track must be fastened to a flat surface such as a wall or clamped to a truss or 
similar structure. Do not apply power to the product if it is not securely fastened! 
 

WARNING! A track shall be secured with minimum one clamp at each track joint and where the 
track ends, including each running meter of a solid track! 

 

Fastening the tracks to a surface or truss 

The track system is based on the UniBeam system, and the standard product comes in steps of 1m 
up to 6m, or the length can be customized on request. 
 
The tracks shall be positioned only vertically and fastened to a flat surface such as a wall or truss. 
Check that the entire surface can support at least 10 times the weight of all the equipment to be 
installed on it, and that the installation respects all locally applicable regulations. 
 
As a common rule, a track shall always be secured with minimum one clamp at each track joint 
and where the track ends, including each running meter of a solid track. However, this may vary 
depending  on  the  weight  and  distribution  of  the  load.  Consult  Wahlberg  Motions  Design  for 
further guidance and customized solutions like floor stands or multiple units on the same track. 

Accessories 

The following parts are not included the Track Runner Series and shall be ordered separately. 

341.701 1m Track (Rail) 

[A]*1

 

341.702 2m Track 
341.703 3m Track 
341.704 4m Track 
341.705 5m Track 
341.706 6m Track 
 
Or customized lengths 
on request, straight or 
curved (min. radius 2m). 

340.701 1m Track 

[A]*1

 

340.702 2m Track 
340.703 3m Track 
340.704 4m Track 
340.705 5m Track 
340.706 6m Track 
 
Or customized lengths 
on request, straight or 
curved (min. radius 2m). 

343.701 1m Track (Rack and Rail) 

[A]

 

343.702 2m Track 
343.703 3m Track 
343.704 4m Track 
343.705 5m Track 
343.706 6m Track 
 
Or customized lengths 
on request, straight or 
curved (min. radius 2m). 

342.701 1m Track (Rack) 

[A]

 

342.702 2m Track 
342.703 3m Track 
342.704 4m Track 
342.705 5m Track 
342.706 6m Track 
 
Or customized lengths 
on request, straight or 
curved (min. radius 2m). 

344.703  Connection  bracket 

[B]

  (Join  two  or 

more sections of tracks). 
 
 

344.702 Bracket 

[C]

 with Manfrotto clamp for 

pipe or truss mount 42-52mm. 
 
 
 
 
 
 
 

Summary of Contents for Track Runner Series

































Reviews: