background image

12 

Clean the range regularly.  A clean appliance looks better, will last longer and will perform better.   

Carbonised grease on the surface or on the griddle plate (If fitted) will hinder the transfer of heat 

from the cooking surface to the food.  This will result in loss of cooking efficiency. 

 

NOTE:  Each griddle option can be supplied with a scraper tool and a pack of blades for cleaning 

the  griddle  surface.    These  are  not  supplied  with  the  griddle  and  have  to  be  purchased 

separately.  Refer to the 'Replacement Parts List' at the rear of this manual. 

 

DO NOT use water on the griddle plate while this item is still hot as warping and cracking 

may occur.  Allow the griddle plate to cool down before cleaning

 

NOTE: 

 

DO  NOT  use  abrasive  detergents,  strong  solvents  or  caustic  detergents  as  they  could  

corrode or damage the range. 

 

In  order  to  prevent  the  forming  of  rust  on  the  griddle  plate  (Steel  Plate),  ensure  that  any 

detergent  or  cleaning  material  has  been  completely  removed  after  each  cleaning.    The  

appliance  should  be  switched  on  briefly  to  ensure  the  griddle  plate  becomes  dry.    Oil  or 

grease should be spread over the griddle surface in order to form a thin protective greasy 

film.

 

 

To keep your range clean and operating at peak efficiency, follow the procedures shown below:- 

 

 

1. 

Clean the griddle with a scraper tool to remove any food debris. 

2. 

Always ensure that the scraper tool blades are changed regularly to ensure that the scraper tool 

works efficiently and prevents damage to the griddle plate surface. 

 

Radiant Elements 

 

a.  Wipe the surface while the radiant elements are still warm to remove overspills, grease etc. 

before they harden. 

b.  As soon as elements have cooled, wipe all over with a damp cloth. 

c.  Raise the side of the element module and withdraw, clean and dry the spill-over dish. 

 

Always turn off the electrical power supply at the mains supply before cleaning. 

This appliance is not water proof. 

Do not use water jet spray to clean interior or exterior of this appliance. 

 

T

HE

 

BLADES

 

FITTED

 

TO

 

THE

 

SCRAPER

 

TOOL

 

ARE

 

EXTREMELY

 

SHARP

 

AND

 

ARE

 

TO

 

BE

 

USED

 

WITH

 

CARE

 

 

Summary of Contents for RNL8610E Series


























Reviews: