3
RN[1]8610E
Electric Range Static Oven + 6 Radiant Elements.
RN[1]8613E
Electric Range Static Oven + 4 Radiant El 300 mm Griddle.
RN[1]8616E
Electric Range Static Oven + 2 Radiant El 600 mm Griddle.
RN[1]8619E
Electric Range Static Oven + 900 mm Griddle.
RN[1]8610EC
Electric Range Convection Oven + 6 Radiant Elements.
RN[1]8613EC
Electric Range Convection Oven + 4 Radiant El 300 mm Griddle.
RN[1]8616EC
Electric Range Convection Oven + 2 Radiant El 600 mm Griddle.
RN[1]8619EC
Electric Range Convection Oven + 900 mm Griddle.
NOTE:
[1]: - Model Options;
-
- Standard.
L
- Low Back.
B
- Bold Front.
LB
- Low Back and Bold Front.
A commercial heavy duty, 900 mm wide Electric Range designed for modular kitchens and is
constructed in an easy clean stainless steel external finish.
The range is fitted with either a 900 mm 6.5kW electric static oven or convection oven.
The hob is divided into modular sections of griddle plates and radiant elements (solid or open).
Electrical supply connection point is located at the rear of the appliance, approximately 80mm from
the right hand side, 466mm from the rear and 150mm from the floor.
When connecting a this electric appliance to the mains supply, ensure that the following is carried
out:-
An isolating switch is fitted within 2m of the appliance, but not on the appliance and in
such a position that the user does not have to reach across the cooking surface.
Supply cord shall be oil-resistant, sheathed flexible cable and not lighter than ordinary
polychloroprene or other equivalent synthetic elastomer sheathed cord (as per AS / NZS
3191 part 2.10.11. or IEC 60245-IEC-57) e.g. HO5 RN-F Type.
The branch supply line shall be individually overload protected to the correct current rating
and the supply chord shall be protected against any mechanical or thermal damage.
A grommet is fitted around the wiring entry hole into the appliance.
Supply cable wires should be boot laced and all terminal connections must be tight to avoid
potential self-overheating.
Refer to the appropriate wiring standards for the size of cable that is to be supplied to an appliance
for the current drawn on that line.
T
HIS
APPLIANCE
MUST
BE
EARTHED
.
I
F
THE
SUPPLY
CORD
IS
DAMAGED
,
IT
MUST
BE
REPLACED
BY
A
SUITABLY
QUALIFIED
PERSON
IN
ORDER
TO
AVOID
A
HAZARD
.
Model
Total Power
Input
Amps @ 400 - 415 Vac
Motor
Power Supply
Voltage
Type
Frequency
L1
L2
L3
RN8610E
400-415 Vac
3 P+N+E
50 / 60 Hz
20.9 kW
28.3
29.4
29.4
----
RN8613E
400-415 Vac
3 P+N+E
50 / 60 Hz
19.7 kW
22.5
29.4
29.4
----
RN8616E
400-415 Vac
3 P+N+E
50 / 60 Hz
18.5 kW
22.5
23.6
29.4
----
RN8619E
400-415 Vac
3 P+N+E
50 / 60 Hz
17.3 kW
22.5
23.6
23.6
----
RN8610EC
400-415 Vac
3 P+N+E
50 Hz
21.2 kW
28.7
29.4
29.4
100W
RN8613EC
400-415 Vac
3 P+N+E
50 Hz
20.0 kW
22.9
29.4
29.4
100W
RN8616EC
400-415 Vac
3 P+N+E
50 Hz
18.8 kW
22.9
23.6
29.4
100W
RN8619EC
400-415 Vac
3 P+N+E
50 Hz
17.6 kW
22.9
23.6
23.6
100W
