background image

11 

Operation 

Operation Guide 

1. 

Waldorf Salamanders have been designed to provide simplicity of operation and 100% safety  

protection. 

2. 

Improper operation is almost impossible, however bad operation practices can reduce the life of the 
salamander and produce a poor quality product.  To use this salamander correctly please read the 

following sections carefully:- 

 



Lighting the Main Burners. 



Racking System. 



Cooking Recommendations. 

 

Description of Controls 

The salamander has individual heat controls for left and right sides.  Select desired heat level and allow a 

few minutes for elements to heat up. 

 



Waldorf salamanders provide two independently controlled heat zones. 



High speed grilling is provided by two infrared gas burners in ceiling of grilling compartment. 



Left hand and right hand gas control knobs operate the left side and right side burners respectively, 
independently of each other. 



Each burner is provided with piezo ignition and flame failure protection for main burner. 

Gas Control Knobs 

 

 

    OFF Position. 

  HIGH Flame. 

  LOW Flame. 

Rack Handles

 

Fig 6 

Piezo Igniter 

 

 
 



This appliance is for professional use and is only to be used by qualified 
persons. 



Only authorised service persons are to carry out installation, servicing or gas 
conversion operations. 



Components having adjustments protected (e.g. paint sealed) by the 

 

manufacturer should not be adjusted by the user / operator. 

Caution 

Summary of Contents for SN8200G























Reviews: