background image

DECLARATION OF CONFORMITY

International standards to which conformity is declared:

Recreational Craft Directive, RCD: 94/25/EC, Module A

International Organization for Standardization, ISO: 6185-1/2/3

American Boat and Yacht Council, ABYC: H-28

National Marine Manufacturers Association, NMMA: H-28

CERTIFYING BODIES

Europe

United States of America

MANUFACTURER

TYPE OF EQUIPMENT • TYPE ‘D’

Inflatable Boat

HULL IDENTIFICATION NUMBER

HIN / CIN (Found on boat transom): US-EWV___________________

IMPORTER

This Owner’s Safety Manual and all its components are copyrighted materials of Walker Bay®. All rights reserved.

IMCI

Langstr. 89

B-4731 Eynatten, Belgium

Tel: 32 87 30 65 30

Fax: 32 87 30 65 36

info@imci.org

ICNN

40 Avenue du Lazaret   

17 000  La Rochelle, France

Tel: 33 (0) 5 46 28 32 24

Fax: 33 (0) 5 46 34 04 66

contact@icnn.fr

National Marine Manufacturers Assn.

Suite 5100-200 E. Randolph Dr.

Chicago, IL 60601-6528, USA

Tel: 1 (312) 946-6214

Fax: 1 (312) 946-0388

Walker Bay Boats, LLC

3555 Bay Street

Union Gap, WA

98903-1887

www.walkerbay.com

Customer Service

email: info@walkerbay.com

Summary of Contents for Genesis


















Reviews: