Walker WP3211LCD, Operating Instructions Manual

English   

- 13 -

If an active antenna is connected to your TV, you can 
select this option as On. Antenna power should be 
“Off” when standard antenna is used instead of the 
active antenna. See “

Con

fi

 guration  Menu

” in the 

following sections for more information. 
Press 

OK

 button on the remote control to continue 

and the following message will be displayed on the 
screen:

• To select the “Yes” or “No” option, highlight the item 

by using “ ” or “ ” buttons and press 

OK

 button.

The IDTV will automatically tune to the  transmission 
channels, searching for digital terrestrial TV broadcasts 
and displaying the names of channels found. This 
process will take a few minutes. To cancel searching, 
you can press 

“M”

 button at any time during the 

process. The following OSD will be displayed during 
the automatic search:

After Automatic Search is completed, the following 
message will be displayed, asking for sorting option. 
If you select “YES”, programme list will be sorted 
according to LCN (logical channel number). Select 
“NO” for using frequency sort. (This feature is available 
for only Germany,Austria and Italy country option).

After this operation, the following menu will appear on 
the screen, asking for analog channel search:

To search for analogue channels, select “Yes”.  TV 
switches to the analogue TV mode. A menu will be 
displayed to search for analogue channels .  
 Set 

Language

 item by pressing “ ” or “ ” button. 

Press “ ” or “ ” button to highlight 

Country

 item and 

then use “ ” or “ ” to set. Press “ ” or “ ” button to 
highlight 

TXT. Language

. Set TXT Language by using 

“ ” or “ ” button. To cancel, press the 

BLUE

 button.

When 

fi

 nished, press 

OK

 or 

RED

 button to continue 

and the following OSD will be displayed: 

After 

automatic tuning

 is 

fi

 nalized, a programme list 

will appear on the screen. In the programme list you 
will see the programme numbers and names assigned 
to the programmes.
If you do not accept the locations and/or the names 
of the programmes, you can change them in Program 
table. For details, see the section, “Program table”.

 General Operation

  Pressing the 

‘‘DTV/USB’’ 

button at any time while 

watching television programmes will switch the TV 
set to the digital terrestrial television broadcasting.

Information Banner

• Whenever you change the channel using the 

P + 

or

P -

 button or numeric buttons, the TV displays the 

broadcast picture along with an information banner 
at the bottom of the screen. This will remain on the 
screen for approximately a few seconds. 

• The information banner can also be displayed 

by pressing the 

“INFO”

 button at any time while 

watching the TV. Pressing 

“INFO”

 button again 

removes the banner.

If the selected channel is locked, you must enter 
the correct four digit key to view the channel. In this 
case, a dialog box asking for the lock key will be 
displayed:

Electronic Programme Guide (EPG)

Some, but not all, channels send information about 
the current and next events. Please note that event 
information is updated automatically. If there are no 
event information data available for channels,

EPG

will be displayed with blanks.
• Press 

EPG

 button to view the 

EPG

 menu.

[GB]_MB36_MASQUE_HDIDTV-MPEG4_BRONZE8_32843W_1205UK_10069999_50176032.indd   13

[GB]_MB36_MASQUE_HDIDTV-MPEG4_BRONZE8_32843W_1205UK_10069999_50176032.indd   13

06.09.2010   09:12:09

06.09.2010   09:12:09