background image

WX520 / WX520L / WX520T
Log Splitter

Introduction

3

1.  Introduction

 WARNING!

Do not attempt to start or operate the machine 

before you read this manual thoroughly. Make 

sure that you understand how to operate the 

machine correctly and safely before you use it.
Keep this manual with the machine at all times.

W034

1.1  Foreword

Congratulations on your choice of a Wallenstein WX520 Log 
Splitter!

This high-quality machine is designed and manufactured to 
meet the needs of an efficient wood splitting operation. 

This manual covers the Wallenstein 20-ton WX520 trailer log 
splitters. The WX520 models are horizontal splitting only. 

Models Covered in this Manual

•  WX520
•  WX520L

 (stop, turn signal, tail lights)

•  WX520T 

(tall frame)

Information that is specific to a model is noted. Otherwise, the 
information in this manual applies to all of the listed models.

Units of measurement in Wallenstein Equipment technical 
manuals are written as:  
US Customary (SI metric).

Keep this manual handy for frequent reference and to pass 
on to new operators or owners. Call your Wallenstein dealer 
or distributor if you need assistance, information or additional 
copies of the manuals.

Wallenstein Equipment Inc. • © 2023. All rights reserved.

No part of this work may be copied, reproduced, replaced, 
distributed, published, displayed, modified, or transferred in 
any form or by any means except with the prior permission of 
Wallenstein Equipment Inc.

Review all safety, operation and maintenance information 
contained in this manual.

Summary of Contents for WX520









































Reviews: