background image

WX900 Series
Log Splitter

Operating Instructions

19

6.  Operating Instructions

Wallenstein WX900 Series log splitters are self-contained 
machines designed to push wood through a wedge to split it. 

The operator has the responsibility of being familiar with all 
operating and safety procedures and following them.

6.1  Operating Safety

 WARNING!

Wear the personal protective equipment (PPE) 

that is required to complete the work safely.
This includes, but is not limited to a hard hat, 

hearing protection, a face shield, protective 

footwear, a respirator, and heavy gloves.

W101

 WARNING!

Always use the machine outdoors and park 

the machine in a position where the prevailing 

winds blow the engine exhaust away from the 

operator. Exhaust from the engine contains 

carbon monoxide (CO) that can accumulate to a 

dangerous level, even in an area with good air 

fl ow.

W006

 WARNING!

Risk of pinching or crushing hazard between the 

wedge or push block and the log! 
Never place hands at the ends of the log. 

Always grasp logs by the sides when loading or 

removing.

W035

• 

Read and understand this manual before you start the 
machine. Review all safety information annually.

• 

Park the machine in a clear location on dry, level ground. 
Do not operate the machine on a hillside or area that is 
cluttered, wet, muddy, or icy to prevent slips, trips, and 
falls.

• 

Keep the work area clean and free of debris.

• 

Only operate the engine in a location that has good air 
flow. Engine exhaust gases contain carbon monoxide (an 
odorless gas) that can cause asphyxiation.

• 

Attach all guards and shields, and close all covers before 
starting the machine. If a guard, shield, or cover was 
removed, install it.

• 

Do not move or transport the machine when the engine is 
on.

• 

Stop the engine before leaving the machine unattended. 

• 

Do not put your hands near the wood being split. 

• 

Do not step over or straddle the log splitter during 
operation.

• 

Do not try to split more than one log at a time. The logs 
may be ejected from the log splitter and cause injury.

• 

Keep your fingers and hands away from cracks in the log 
that can open while splitting.

• 

Always load logs by holding the middle of the log, not the 
cut ends.

• 

Do not reach into or load the log splitter when the wedge is 
moving.

• 

Do not try to split logs across the grain. Some types of 
wood can burst or splinter causing pieces to be ejected, 
causing injury.

• 

For unevenly cut logs, always place the square cut end 
against the splitting wedge.

• 

Never stand, sit, or climb on any part of the machine, 
especially while the engine is on.

• 

Never operate the machine alone. Always have a minimum 
of two trained people:

• There should be one operator and one spotter present 

during machine operation. The operator and spotter 
must know all the machine safety, controls, and 
operating functions.

• The operator must be in control of the machine at all 

times. The spotter must stay outside of the hazard zone 
while the machine is operating.

Summary of Contents for WX900 Series

















































Reviews: