background image

 

 

   

 

 

Revision 7 

22 

operated by pressing the button at the rear cover next to the illuminated mains 
switch. Press the soap prime button until soap begins to consistently dispense 
from the basin nozzle. 

  Soap levels should be checked periodically depending on usage to maintain 

efficient operation of the unit. The system should be washed through with 
warm water periodically to remove any solidified soap within the tubing & 
nozzle as follows: Remove the soap tube from the soap container, place the 
free end of soap tube into a beaker or container of WARM water & using a 
continuous press of Soap Prime button, flush WARM water through the 
system. 

 

11.4 Water Temperature & Flow 

 
NOTE: Due to the anti-ligature design the basin area is relatively shallow. The 
flow rate of water is therefore regulated to a low level to avoid water over 
spilling the basin lip. 

  The hand wash water temperature is governed by the flow rate which is set by 

a flow regulator built into the water system at a rate of 1.8LPM. This flow rate 
may slightly vary due to the water supply pressure and tolerance of the 
regulator. 

  Water temperature can also be affected by changes to the ambient 

temperature of the incoming cold supply which may happen seasonally 
depending on the nature of the water supply. 

  The cold water outlet if fitted is also fitted with a flow regulator (0.8LPM). 

11.5 Maintenance 

 

  Wallgate operates a comprehensive spare parts service. Contact our service 

department for all spare part & servicing requirements. 
 

WARNING: IN MODELS WITH A WATER HEATER) THE WATER HEATER IS A 
VENTED TYPE AND IN NO CIRCUMSTANCES MUST THE WATER OUTLET 
NOZZLE BE ALLOWED TO BECOME BLOCKED OR CONNECTED TO ANY PIPE 
OR TAP. 
 

  The unit basin fascia must be cleaned with non-abrasive cleaners only, use 

abrasive washbowl cleaners such as standard domestic cleaning products 
dependent upon the level of soiling. Proprietary de-scaling agents may be 
used to remove lime scale from the bowl, and the water nozzle. 

  From 

a user’s point of view, the most important care items are: 

Summary of Contents for PSH-20 Series

























Reviews: