21
MOD.
...........................................................................................
6011 / 6010 / 6010 sp HVLP
Ø
Feed
**Product load
Air consumption at
0.7 bar (10 psi) captest
Fan dimensions
at 20 cm (7.9”)
Delivery
pressure
1.2
1.4
1.7
1.9
2.2
2.5
3.0
180-220 Lt./min (6.4-7.8 CFM)
180-220 Lt./min (6.4-7.8 CFM)
180-220 Lt./min (6.4-7.8 CFM)
180-220 Lt./min (6.4-7.8 CFM)
180-220 Lt./min (6.4-7.8 CFM)
180-220 Lt./min (6.4-7.8 CFM)
180-220 Lt./min (6.4-7.8 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)
15 cm (5.8”)
16 cm (6.2”)
18 cm (7”)
19 cm (7.4”)
20 cm (7.8”)
21 cm (8.2”)
23 cm (9”)
16 cm (6.2”)
17 cm (6.6”)
19 cm (7.4”)
20 cm (7.8”)
21 cm (8.2”)
23 cm (9”)
25 cm (9.8”)
70 Gr/min. (2.5 oz/min.)
90 Gr/min.(3.2 oz/min.)
110 Gr/min.(3.9 oz/min.)
130 Gr/min.(4.6 oz/min.)
160 Gr/min.(5.7 oz/min.)
180 Gr/min.(6.4 oz/min.)
210 Gr/min.(7.5 oz/min.)
110 Gr/min.(3.9 oz/min.)
120 Gr/min.(4.3 oz/min.)
160 Gr/min.(5.7 oz/min.)
190 Gr/min.(6.8 oz/min.)
230 Gr/min.(8.2 oz/min.)
280 Gr/min.(9.9 oz/min.)
340 Gr/min.(12 oz/min.)
Gravity
Gravity
Gravity
Gravity
Gravity
Gravity
Gravity
Suction
Suction
Suction
Suction
Suction
Suction
Suction
SP version
SP version
SP version
SP version
SP version
SP version
SP version
2.5 - 3.0 bar
(36-43 psi)
...
TECHNICAL SPECIFICATIONS
...
USE
...
ADVICE FOR CORRECT USE
...
FORM OF THE FAN
...
ADJUSTMENTS
- Air fitting: G 1/4” M
- Product delivery fitting (version SP): G 1/4” M
- Maximum air pressure: 5 bar (73 psi)
- Maximum product pressure (SP version): 5 bar (73 psi)
- Working pressure: 2.5-3.0- bar (36-43 psi)
- Fan: Fully open
- Air: Fully open
- Product: 4 turns
** Product flow was calculated with water, setting the recommended regulations.
RECOMMENDED AIR PRESSURE DURING USE: 2.5 - 3.0 bar (36-43 psi)
At the recommended air pressure the spray gun respects the European and U.S. ecological norms for which the transfer
efficiency must be above 65% and /or the air pressure at the exit of the air cap must not be superior to 0.7 bar (10 psi).
Spray guns int the 6000 HVLP series have been designed for the application of finishing colours in all those sectors requiring
high quality finishing and low fumes emission.
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
To obtain the best results, the following instructions must be followed carefully:
1.
When possible, use an air pipe with a minimum internal section of ø 8 mm (0.3”).
2.
Make sure the compressed air used is perfectly filtered removing all water, oil or other impurities (for example, by installing
an Asturomec filter regulator ref. 61131 and Asturomec coalescent microfilter ref. 61201, or by the more complete and efficient
WALCOM TD
3
PRO multifunctional filter and heating unit).
1. The distance between the spray gun and the surface to be painted must be set between 100 and 150 mm (3.9”- 5.9”).
If the spray gun is working at too low a pressure and at too high a distance, il will not perform to the best of its capacity.
2.
The jet from the spray gun must always be perpendicular to the surface being
painted and the paint must be applied in horizontal strokes. Any eventual shift from
this position when spraying will result in an uneven application of the paint layer.
3.
Correct viscosity of the paint is between 15 and 25 sec. Coppa Ford n. 4. These
values depend on the application in question and the measure of the nozzle in use.
Adjust the air pressure, product quantity and spray aperture
until obtaining a regular imprint as in fig. C
- Air pressure too low
- Product viscosity too high
- Quantity of product too high
- Air pressure too high
- Product viscosity too low
- Quantity of product too low
- Regular jet
Summary of Contents for Asturomec 6010 sp HVLP
Page 66: ...Note ...
Page 67: ...Note ...
