60
Ø
подача/
бачок верн/нижн/SP
**расход краски
гр/мин
возд.поток
л/мин
диаметр пятна
с 20 см (7.9”)
давление
бар
3.0
4.0
5.0
180-220
л/мин
(6.4-7.8 CFM)
180-220
л/мин
(6.4-7.8 CFM)
180-220
л/мин
(6.4-7.8 CFM)
180-240
л/мин
(6.4-8.5 CFM)
180-240
л/мин
(6.4-8.5 CFM)
180-240
л/мин
(6.4-8.5 CFM)
18 cm (7.1”)
20 cm (7.9”)
24 cm (9.4”)
512 Gr/min.(18 oz/min.)
676 Gr/min.(23.9 oz/min.)
730 Gr/min.(25.8 oz/min.)
Верхний
Верхний
Верхний
SP
SP
SP
2.5-3.0 bar
(36-43 psi)
Модели
.
............................................................
9011 GEL COAT - 9010 sp GEAL COAT
...
Технические характеристики
...
Применение
...
Рекомендации по правильному применению
...
Pегулировки
- Подсоединение сжатого воздуха-винтовой разъем G 1/4” M
- Подсоединение для подачи краски (вариант SP) G 1/4” M
- Максимальное давление воздуха: 5 бар (73 psi)
- Максимальное давление продукта (модификация SP): 5 бар (73 psi)
- Рекомендуемое рабочее давление 2.5-3.0 бар (36-43 psi)
- Форма факела: вентиль полностью открыт
- Расход воздуха: вентиль полностью открыт
- Расход ЛКМ: винт 2.5-3 оборота от положения «закрыто»
** Подача продукта была определена с водой, используя рекомендуемые настройки.
Аэрографы линии Novemila GEL COAT разработаны для нанесения средства GEL COAT и прочей вязкой продукции.
Инструмент не предназначен для нанесения средств, содержащих абразивные вещества, кислоты или бензин.
Для обеспечения оптимальных результатов рекомендуем внимательно придерживаться следующих рекомендаций:
Для достижения наилучшего результата следует выполнять следующие требования:
1.
Использовать магистраль подачи воздуха внутренним диам не менее 8 мм (0.3”).
2.
Убедиться в том, что используемый сжатый воздух не содержит воды, масла и других загрязняющих веществ (например, можно установить
фильтр-регулятор Asturomec сс. 61131 и коалесцентный микрофильтр Asturomec сс. 61201 или более сложную и эффективную систему
фильтрации наряду с многофункциональной системой распыления WALCOM TD
3
PRO).
1. Расстояние между аэрографом и покрасочной поверхностью должно составлять от 150 до 200 мм (5.9 - 7.9 дюймов).
Если давление в
аэрографе низкое, а расстояние слишком большое, его работа будет неэффективной.
2.
Струя должна направляться перпендикулярно поверхности, которую окрашивают.
Краска должна наноситься в горизонтальном направлении.
Возможное отклонение струи от оси во время покраски может привести к
неоднородному наложению слоя краски.
...
Форма факела
для получения факела типа “С” установить правильное входное
давление, подачу продукта, расход воздуха на факел.
низкое давление
густая краска
излишек продукта
высокое давление
низкая вязкость краски
излишек продукта
правильная
форма
факела
Summary of Contents for Asturomec 6010 sp HVLP
Page 66: ...Note ...
Page 67: ...Note ...