background image

Limited Warranty

Products manufactured by Walrus Pumps Co (Walrus) are warranted to the first user only 

to be free of defects in material and workmanship for a period of 12 months from date of 

installation, but no more than 24 months from date of shipment. Walrus' liability under this 

warranty shall be limited to repairing or replacing at our election, without charge, FOB 

Walrus' distribution center or authorized service agent. Walrus will not be liable for any 

cost of removal, installation, transportation or any other charges that may arise in 

connection with warranty claim.

The warranty period commences on the date of original purchase of the equipment. Proof 

of purchase and installation date, failure date, and supporting installation data must be 

provided when claiming repairs under warranty.

This warranty is subject to due compliance by the original purchaser with all directions and 

conditions set out in the installation and operating instructions. Failure to comply with 

these instructions, damage or breakdown caused by fair wear and tear, negligence, misuse, 

incorrect installation, inappropriate chemicals or additives in the water, inadequate 

protection against freezing, rain or other adverse weather conditions, corrosive or abrasive 

water, lightning or high voltage spikes or through unauthorized persons attempting repairs 

are not covered under warranty.  

Walrus will not be liable for any incidental or consequential damages, losses, or expenses, 

arising from installation, use, or any other causes. There are no express or implied 

warranties, including merchantability or fitness for a particular purpose, which extend 

beyond those warranties described or referred to above.

Certain states do not permit the exclusion or limitation of incidental or consequential 

damages or the placing of limitations on the duration of an implied warranty, therefore, the 

limitations or exclusions herein may not apply. This warranty sets forth specific legal rights 

and obligations, however, additional rights may exist, which may vary from state to state.

Supersedes all previous publications

CP70D0008D500EW0R

02

WALRUS PUMP CO., LTD.

Web: www.walruspump.com

Summary of Contents for TQCN1500













Reviews: