25
24
Contents
Exploded Drawing
2
Declaration of CE-Conformity
25
Replacement parts
26
1 General
30
1.1
Identification of Model Version
30
1.2
Normal Use
30
1.3
Improper Use
31
2
Technical Description
31
3
Safety Warnings
32
3.1
Safety Warting Symbols
32
3.2
Generally Applicable Safety Precautions
32
4
Assembly / Installation
33
4.1
Mounting of Spray Gun
33
4.2
Connection of Input Lines
33
5
Operational Handling
34
5.1
Safety Warnings
34
5.2
Starting/Stopping Requirements
34
5.3
Spray Pattern Test
34
5.4
Spray Pattern Adjustments
35
5.5
Correcting of Spray Pattern Imperfections
36
5.6
Retooling of Spray Gun
36
6 Cleaning
37
6.1
Safety Warnings
37
6.2
Cleaning - Complete
37
6.3
Cleaning - Routine
38
7
Repairs / Replacements
39
7.1
Replacement of defective Needle Seal Packings
39
7.2
Replacement of Nozzles, Needles, Springs
39
and Seals
8
Trouble shooting and Corrective Action
40
9
Disposal of Cleaning / Servicing Substances
40
10
Specification Data
41
EC/EU Declaration ofConformity
We, the manufacturers of the equipment, hereby declare under our sole responsibility that the product(s)
described below conform to the essential safety requirements. This declaration will be rendered invalid if any
changes are made to the equipment without prior consultation with us.
Manufacturer
WALTHER Spritz- und Lackiersysteme GmbH
Kärntner Str. 18 - 30
D - 42327 Wuppertal
Tel.: +49(0)202 / 787 - 0
Fax: +49(0)202 / 787 - 2217
www.walther-pilot.de • e-mail: info@walther-pilot.de
Type Designation
Automatic Spray Gun
PILOT WA 705
-Serie
without internal control
WA 705
(Standard)
V 20 705
WA 715-U
(Standard-circulation)
V 20 715
WA 725-HVLP
(Low pressure)
V 20 725
WA 735-HVLP-U
(Low pres.-circulation)
V 20 735
WA 745-HVLP
PLUS
(Medium pressure)
V 20 745
WA 755-HVLP
PLUS
-U (Medium pres.-circulation)
V 20 755
WA 708-K
(Standard-adhesive version)
V 20 708
WA 718-U-K
(Standard-adhesive vers.-circul.)
V 20 718
WA 728-HVLP-K
(Low pressure-adhesive version)
V 20 728
WA 738-HVLP-U-K
(Low pressure-adhesive vers.-circul.)
V 20 738
Intended purpose
Processing of sprayable media
Applied Standards and Directives
EU-Mechanical Engineering Directives 2006/42/EC
2014/34/EU (ATEX Directives)
DIN EN ISO 12100
DIN EN 1953
DIN EN 13463-1
DIN EN 1127-1
DIN EN 13463-5
Specification according 2014/34/EU
Category 2
Part marking
II 2 G c T 5
Tech.File,Ref.:
2414
Authorized with the compilation of the technical file:
Nico Kowalski, WALTHER Spritz- und Lackiersysteme GmbH, Kärntner Str. 18 - 30
D- 42327 Wuppertal
Special remarks :
The named product is intended for installation in other equipment. Commissioning is prohibited until such
time as the end product has been proved to conform to the provision of the Directives 2006/42/EC.
Wuppertal, the 2nd of November 2016
Name: Torsten Bröker
Position: Manager, Design and Development
This Declaration does not give assurance of properties in the sense of product liability. The safety instructions
provided in the product documentation must be observed at all times.
p.p.
