background image

Next, plug the 

cable

cable

cable

cable

 into the 

Power Supply

Power Supply

Power Supply

Power Supply

, and the 

Power Supply

Power Supply

Power Supply

Power Supply

 into the power input port, next to the power switch. 4.7Before 

connecting anything, make sure that the Duplicator 3/4power switch is in the 

OFF

OFF

OFF

OFF

 position.

 

 

Now locate the 

USB A to B cable

USB A to B cable

USB A to B cable

USB A to B cable

 and plug it into the USB B port on The Duplicator 3. Don’t plug the other end into anything yet.

 

Last, open up your box(es) of 

filament

filament

filament

filament    

and mount them on the 

Spool holder(s

Spool holder(s

Spool holder(s

Spool holder(s))))

. Mount each spool so that the filament feeds up from 

the center.

 

You'll need to squeeze the spool holder to fit the spool onto it. When it's all the way on, the spool will lock into place.

 

Guess what? You’re done with initial hardware setup! Take a moment to relax and mentally prepare yourself for what lies ahead. 

When you’re ready to flip the switch and make your first prints, head to the next step, the 

First Run Experience

.

 

 

Summary of Contents for Duplicator 3/4














Reviews: