WANHAO DUPLICATOR 7, User Manual

Electrical  power

This  3D  printer  is  connected  to  the  electrical  network  with  an  INPUT  of  110  or  240  VAC,  

50/60  Hz,  and  has  an  operational  voltage  of  12  V.

-­      Do  not  allow  anything  to  rest  on  the  power  cord.  Do  not  locate  this  product  where  

          people  will  walk  on  the  cord.

-­      If  an  extension  cord  is  used  with  this  product,  make  sure  that  the  total  ampere  rating

        of  the  equipment  plugged  into  the  extension  cord  does  not  exceed  the  extension  

        cord  ampere  rating.  Also,  make  sure  that  the  total  rating  of  all  products  plugged

        into  the  wall  outlet  does  not  exceed  the  fuse  rating.

-­      Do  not  overload  a  power  outlet,  strip  or  receptacle  by  plugging  in  too  many  devices.

-­      Use  the  product  only  with  the  supplied  power  supply  cord  set.  If  you  need  to  

          replace  the  power  cord  set,  make  sure  that  the  new  power  cord  meets  the  

¯ŸĶĶŸɠÞضNjsLJȖÞNjsŎsŘǼǣʲ_sǼOÌEĶsǼɴƼsʰȕĵĶÞǣǼs_ˀNǢOsNjǼÞʩs_ʰə^rƼƼNjŸɚs_

          or  its  equivalent,  4.5  meters  (15  feet)  maximum

-­        In  case  of  malfunction  disconnect  the  printer  immediately  from  network.

˚^ŸŘŸǼǼǼsŎƼǼǼŸʩɮǼÌÞǣƼNjŸ_ȖOǼEɴɴŸȖNjǣsĶ¯ʰǣŸƼsŘÞضŸNjNjsŎŸɚÞضOŸɚsNjǣŎɴ

          expose  you  to  dangerous  voltage  points  or  other  risks.  Refer  all  reparation  to

LJȖĶÞʩs_ǣsNjɚÞOsƼsNjǣŸŘŘsĶʳ®ŸNjOŸŘǼOǼǼÌsǼsOÌŘÞOĶǣsNjɚÞOsƼĶsǣsǣsŘ_ŘsŎÞĶ

          to  your  national  supplier  or  www.wanhao3dprintr.com

ȕŘƼĶȖ¶ǼÌÞǣƼNjŸ_ȖOǼ¯NjŸŎǼÌsɠĶĶŸȖǼĶsǼŘ_Njs¯sNjǣsNjɚÞOÞضǼŸLJȖĶÞʩs_ǣsNjɚÞOsƼsNjǣŸŘŘsĶ

when:

-­      The  power  cord  or  plug  is  damaged,  cut  or  frayed.

-­      Liquid  was  spilled  into  the  product.

-­      The  product  was  exposed  to  rain  or  water.

-­      The  product  has  been  dropped  or  the  case  has  been  damaged.

-­      The  product  exhibits  a  distinct  change  in  performance,  indicating  a  malfunction.

-­    The  product  does  not  operate  normally  after  following  the  operating  instructions.

-­      Keep  the  printer  out  of  the  reach  of  small  children.

Disposal  instructions

Do  not  throw  this  electronic  device  into  the  waste  when  discarding.  To  minimize  pollution  and  

ensure  utmost  protection  of  the  global  environment,  please  recycle  or  return  to  Photocentric  

for  recycling.

AFTER  SALES  SUPPORT

86-­571-­23290996

support@wanhao3dprinter.com

Model  :  Duplicator  7

6