background image

CONSTRUCT AND CONNECT [

CONT.]

3

Tighten the locking 

bolt clockwise. Then 

install the other Z 

axis pillar onto the 

Base.

Loose the two locking 

bolt on No.3 and No.4 

Z axis pillar by around 

5mm. So there will be 

sufficient space for X axis 

pillar to slide in. 

4

5

Slide the X axis pillar into 

the No.3 and No.4 bolts. If 

there’s not enough space, 

you may need to re-loose 

the locking bolt. 

To tighten the locking 

bolt through the hole on 

top of the X axis pillar. 

Lock both No.3 and No.4 

pillar. 

6

7

Insert the plastic cover 

onto the two ends of X 

axis pillar.  

Note:

 Please double 

check the Z axis and X 

axis pillars. If any bolt 

not secured. You need 

to secure the screws to 

ensure the gantry are 

steady and tight. 

Rotate the cylinder holder 

for a bit but not too close. 

Tight enough that can not 

slide into pillar freely.

This is also same to the 

other side with stickers 

No.6.

8

9

Mount the X axis rail. 

Align the right and left 

side holders first. Please 

make sure the rail is 

located in the middle 

of the X axis. You may 

need to adjust the 

distance to both ends 

through the cylinder 

holders. 

Then tighten the bolts 

on both end of No.5 and 

No.6.

10

11

Mount the MK12 

extruder onto the 

X axis holder. Make 

sure the locking holes 

match to the holder 

holes. 

A total of 4 bolts need 

to be tightened, but the 

first bolt should not be 

too tight until the other 

three bolts are mounted, 

then tighen all the bolts 

together.

12

WIRING INSTRUCTION

B

C

LEVELING BEFORE PRINTING

2

1

Turn the couple to lower the 

two Z axis in order to level 

the two Z axis at same height. 

Note: The ruler or height 

gauge would provide more 

accurate height for both two 

Z axis. The two axis need to 

be at same height. 

3

Turn on the printer.  

Release the 4 bed 

leveling nuts by 4-5 

turns. Then Click LEVEL.

Read the instruction, then 

click NEXT. 

Summary of Contents for DUPLICATOR 9

Page 1: ...ng Package Contents 1 x WANHAO 3D Printer 1 x Filament Spool Holder 1 x Filament Spool Stand 1 x Power Cable 1 x USB Cable 1 x 8GB SD Card 1 x Hex Screw Driver 1 x Hex Key Set 6 x Hex Bolts 2 x Plastic belts 1 x 1 75mm PLA Filament 1 x Needle for unclugging nozzle ASSEMBLING AND MOUNTING 1 Take out all components from the box and place them on the flat ground 1 Base 2 Z axis Tower Pillar 2 3 X axi...

Page 2: ...llars If any bolt not secured You need to secure the screws to ensure the gantry are steady and tight Rotate the cylinder holder for a bit but not too close Tight enough that can not slide into pillar freely This is also same to the other side with stickers No 6 8 9 Mount the X axis rail Align the right and left side holders first Please make sure the rail is located in the middle of the X axis Yo...

Page 3: ...n order to level the two Z axis at same height Note The ruler or height gauge would provide more accurate height for both two Z axis The two axis need to be at same height 3 Turn on the printer Release the 4 bed leveling nuts by 4 5 turns Then Click LEVEL Read the instruction then click NEXT ...

Page 4: ...o move extruder down Stop clicking until you feel the leveling card getting friction while moving the card Click NEXT to initiate auto leveling 7 Congratulation You have finished bed leveling For video installation please scan the QR code Video Installation Official Website Wanhao Store To move the extruder by hand to 4 corners separately Adjusting the knob at each corner until you feel friction w...

Reviews: