background image

15

WARRANTY 

RIAWATECH A/S WARRANTY  

RiaWatech will remedy defects in material and/or workmanship in any new RiaWatech valve for a period of two (2) years 

from the documented date of purchase so long as the valve has been used in accordance with RiaWatech´s instructions 

and recommendations and under normal operating conditions. The warranty does not cover damage to the valve 

caused by external mechanical forces, such as interference from humans, animals or machines, nor is the warranty valid 

if the valve has been modified or altered in any way post-production. Furthermore, the warranty is not valid (a) if the 

valve is damaged due to exposure to high concentrations of chemical substances, (b) if the valve is damaged because 

of pressure spikes, water hammering or vacuums exceeding the rated limits, (c) the warranty is invalid if flow velocity 

exceeds what is recommended, and (d) if malfunctions are caused by other equipment.

To request warranty service, the buyer should contact the WaGate dealer where the valve was purchased within a 

reasonable time after discovering any defects. The valve serial number or order number must be quoted in the case of 

a warranty claim. RiaWatech´s liability is limited to the replacement or repair of the defective valve. RiaWatech will not 

assume costs incurred for removal of defective valves or subsequent installation of replacement valves. Furthermore, 

RiaWatech will not assume transportation costs of damaged valves or replacement valves. RiaWatech warrants that 

repaired or replaced valves are covered for the greater of either the remainder of the original valve warranty or 90 days.  

THE WARRANTY EXPRESSED ABOVE SHALL BE IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED, 

INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS 

FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT WHICH ARE EXPRESSLY DISCLAIMED, AND IS IN LIEU OF 

ANY AND ALL OTHER OBLIGATIONS OR LIABILITY ON RIAWATECH´S PART. TO THE MAXIMUM EXTENT PERMITTED 

BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES WILL RIAWATECH BE LIABLE TO BUYER FOR ANY INDIRECT, 

INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING ANY DAMAGE FOR LOSS OF REVENUE OR 

PROFIT), OR OTHERWISE ARISING OUT OF OR IN CONNECTION WITH FURNISHING OF THE VALVES, PARTS OR SERVICE 

HEREUNDER, OR THE PERFORMANCE, USE OF, OR INABILITY TO USE ANY OF THE VALVES, PARTS OR SERVICE, OR 

OTHERWISE, WHETHER BASED IN CONTRACT, WARRANTY, TORT, INCLUDING WITHOUT LIMITATION, NEGLIGENCE 

OR ANY OTHER LEGAL OR EQUITABLE THEORY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE 

REMEDIES SET FORTH IN THIS LIMITED WARRANTY SHALL APPLY EVEN IF SUCH REMEDIES FAIL THEIR ESSENTIAL 

PURPOSE. FOR THE AVOIDANCE OF DOUBT, NO EMPLOYEE, AGENT OR OTHER REPRESENTATIVE OF RIAWATECH IS 

AUTHORIZED TO EXTEND OR OTHERWISE MODIFY THE WARRANTY SPECIFIED HEREIN.

SVL and RVL

Summary of Contents for WAGATE SVM-TG125

















Reviews: