WAREMA Venetian 2.25/35.17 Operating And Maintenance Instructions Manual Download

Page: 10 / 10

WAREMA Renkhoff SE - Hans-Wilhelm-Renkhoff-Straße 2 - 97828 Marktheidenfeld - Germany

www.warema.com - info@warema.com

EC Declaration of Conformity

The product:

WAREMA venetian blind

Type:

2.25/35.17

Purpose:

Internal sun shading system

Meets the provisions of

Machinery Directive 2006/42/EC

in the case of motor drives.

In particular, the following harmonised standards were used:

DIN EN 13120

Internal blinds - Performance requirements including safety

DIN EN 60335-2-97

Household and similar electrical appliances - Safety - Part 2-97: Particular requirements

for drives for rolling shutters, awnings, blinds and similar equipment

Person in charge of the compilation of the technical documents: Elke Granzer; for address, see manufacturer.

Manufacturer:

WAREMA Renkhoff SE

Hans-Wilhelm-Renkhoff-Str. 2

97828 Marktheidenfeld

Germany

ppa. Ralf Simon

i. A. Elke Granzer

General Management, Research and

Development

Technical Coordination R & D

Marktheidenfeld, August 2016

Summary of Contents for Venetian 2.25/35.17











Search results

Summary of Contents for Venetian 2.25/35.17

Reviews:

Related manuals for Venetian 2.25/35.17

Brands by name

Popular brands

WAREMA Venetian 2.25/35.17, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for Venetian 2.25/35.17

Reviews:

Related manuals for Venetian 2.25/35.17

Brands by name

Popular brands